Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2013.08
RM1440E _58 Vehicle Interior _056165 INTERIOR PANELS / TRIM _0274158 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

Hide 64746F 1.INSTALL DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)

a.

Attach the 2 claws to install the deck side trim cup holder LH.


b.

Install the 4 screws.


Hide 64745H 2.INSTALL DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 62605Q 3.INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)

a.

Attach the 4 claws and 2 guides to install the quarter trim lid sub-assembly RH.


Hide 73372 4.INSTALL REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)

a.

Attach the claw and guide to install the rear seat shoulder belt hanger LH.


Hide 73371 5.INSTALL REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 64754B 6.INSTALL REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)

a.

Attach the claw and 2 guides to install the rear floor finish side plate LH.


b.

Install the 2 screws.


Hide 64753B 7.INSTALL REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 62597A 8.INSTALL SIDE TRIM BOX LH (w/o Rear No. 2 Seat)

a.

Attach the 8 claws to install the side trim box LH.


b.

Install the 2 screws.


Hide 62597A 9.INSTALL SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 64746 10.INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

a.

Attach the 2 claws and 2 guides to install the rear combination light service cover LH.


Hide 64745 11.INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64766 12.INSTALL QUARTER TRIM JACK COVER SUB-ASSEMBLY

a.

Attach the 3 claws and 2 guides to install the quarter trim jack cover sub-assembly.


Hide 62627B 13.INSTALL QUARTER TRIM COVER

a.

Attach the 2 claws to install the quarter trim cover.

HINT:

Use the same procedure for the other quarter trim cover.



Hide 66426B 14.INSTALL REAR NO. 3 SIDE RAIL SPACER LH

a.

Attach the 2 claws to install the rear No. 3 side rail spacer LH.


Hide 66416 15.INSTALL REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 62440 16.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.

Attach the 3 clips to install the roof side rail garnish assembly LH.


Hide 62430 17.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73024 18.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.

Attach the 4 claws to install the front shoulder belt anchor plate sub-assembly LH.


Hide 73023 19.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63310 20.INSTALL ROOF HEADLINING ASSEMBLY

HINT:
B240031

Before installing the roof headlining assembly, move the front seats and rear No. 1 seat to the positions shown in the illustration.


a.

Place the roof headlining assembly into the vehicle through the back door.

NOTICE:

Be careful not to damage the roof headlining assembly when placing it in the cabin.



b.

w/o Sliding Roof:

i.
B354450

Install the roof headlining assembly with the 5 clips.



c.

w/ Sliding Roof:

i.
B354451E03
1.354,1.271 1.948,1.646 1.948,1.646 1.354,1.99 true 1.354,1.51 1.948,1.646 1.948,1.646 1.354,1.75 true 0.813,2.208 1.302,2.875 1.302,2.875 1.24,2.219 true 0.813,1.031 1.313,0.427 1.313,0.427 1.24,1.021 true 0.479,1.26 0.479,0.281 0.479,0.281 0.667,0.281 false 0.49,2 0.49,3.031 0.49,3.031 0.625,3.031 false 1.99,1.563 2.156,1.729 0.167,0.167 10 false *2 1.25,2.906 1.417,3.073 0.167,0.167 10 false *2 1.26,0.229 1.427,0.396 0.167,0.167 10 false *2 0.708,0.198 0.875,0.365 0.167,0.167 10 false *1 0.677,2.938 0.844,3.104 0.167,0.167 10 false *1

Attach the 2 guides and 8 fasteners to install the roof headlining assembly.

Text in Illustration
*1 Guide
*2 Fastener


ii.

Install the 5 clips.



d.

Connect the connector and attach the clamp to the rear pillar RH.


e.

Connect the connector and attach the 2 clamps to the front pillar RH.


f.

Connect the connector and attach the 4 clamps to the front pillar LH.


g.

w/ Sliding Roof:

Connect the sliding roof drive gear connector.


h.

w/ EC Mirror:

Connect the inner rear view mirror assembly connector.


Hide 81240 21.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 87834 22.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 74348 24.INSTALL VISOR HOLDER

a.

Attach the 2 claws.


b.

Push in the visor holder to install it.

HINT:

Use the same procedure for the other visor holder.



Hide 74320 25.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


Hide 74310 26.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74318 27.INSTALL VISOR BRACKET COVER LH

a.

Attach the 4 claws to install the visor bracket cover LH.


Hide 74317 28.INSTALL VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 74631C 29.INSTALL COAT HOOK

a.

Install the coat hook with the screw.


b.

Attach the claw to close the cover.

HINT:

Use the same procedure for the other coat hook.



Hide 74610U 30.INSTALL REAR ASSIST GRIP ASSEMBLY

a.
B131970

Assemble the rear assist grip assembly as shown in the illustration.


b.
B203056

Install the rear assist grip assembly.

HINT:

Use the same procedure for the other rear assist grip assembly.



Hide 74610A 31.INSTALL ASSIST GRIP SUB-ASSEMBLY

a.
B203057

Assemble the assist grip sub-assembly as shown in the illustration.


b.
B203058

Install the assist grip sub-assembly.

HINT:

Use the same procedure for the other assist grip sub-assembly.



Hide 62560C 32.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH

a.

Pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH and attach the 4 claws and 2 guides.


b.

Attach the 7 clips and 4 guides to install the rear window side garnish assembly LH.


Hide 62550F 33.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62580F 34.INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH

a.

w/ Rear No. 2 Seat:

i.

Pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH and attach the 7 claws and guide.



b.

Attach the 6 clips and guide to install the rear No. 2 window side garnish assembly LH.


Hide 62570D 35.INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64740C 36.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.

Pass the rear seatback lock control lever base through the deck trim side panel assembly LH.


ii.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly LH.


iii.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly LH.


iv.

Install the 3 bolts and 2 screws.


v.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/ Rear No. 2 Seat:

i.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly LH.


ii.

Install the 3 bolts and 2 screws.


iii.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


iv.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 64730B 37.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat:

i.

Connect the connector.


ii.

Pass the rear seatback lock control lever base through the deck trim side panel assembly RH.


iii.

Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel assembly RH.


iv.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.


v.

Install the 3 bolts and screw.


vi.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



b.

w/ Rear No. 2 Seat:

i.

Connect the connector.


ii.

Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel assembly RH.


iii.

Install the 3 bolts and screw.


iv.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


v.

Install the rear No. 2 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 64722B 38.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

a.

Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.


b.

Attach the 2 claws to close the cover.

HINT:

Use the same procedure for the other No. 2 luggage compartment trim cover.



Hide 64713F 39.INSTALL FRONT DECK SIDE TRIM COVER LH

a.

Attach the 2 claws to install the front deck side trim cover LH.


Hide 64712F 40.INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64725J 41.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

a.

Push in the No. 1 luggage compartment trim hook to install it.

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook.



Hide 73233A 42.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

a.

Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



Hide 58570C 43.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

a.

Attach the 4 claws to install the rear floor carpet assembly.


Hide 58574A 44.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

a.

Attach the 5 clips to install the rear floor mat rear support plate.


Hide 58306A 45.INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

a.

Install the inner floor side rail sub-assembly with the 4 bolts.


Hide 58480B 46.INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

a.

Attach the 3 clips to install the rear No. 2 floor board assembly.


Hide 58408D 47.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

a.

Attach the 2 clips and 2 guides to install the No. 2 deck board sub-assembly.


Hide 64722B 48.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board)

a.

Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.


b.

Attach the 2 claws to close the cover.

HINT:

Use the same procedure for the other No. 2 luggage compartment trim cover.



Hide 58410R 49.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

a.

Attach the 2 guides to install the deck board assembly.


b.

Install the 6 bolts.


Hide 58704A 50.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

a.

Attach the 4 clips and 2 guides to install the luggage compartment side cover sub-assembly LH.


Hide 58703A 51.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:

Use the same procedure as for the LH side.


Hide 58401A 52.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

a.

Attach the clip to install the No. 1 deck board sub-assembly.


Hide 64721B 53.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

a.

Install the luggage hold belt striker and No. 1 luggage compartment trim cover with the bolt.


b.

Attach the 4 claws to close the cover.

HINT:

Use the same procedure for the other No. 1 luggage compartment trim cover.



Hide 62412 54.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the front seat outer belt floor anchor through the center pillar garnish LH.


b.

Attach the 2 clips and 2 guides to install the center pillar garnish LH.


c.

Install the bolt.


Hide 62411 55.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 56.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 4 claws and 2 clips to install the lower center pillar garnish LH.


b.

Install the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62413A 57.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 58.INSTALL OUTER LAP BELT ANCHOR COVER

a.

Attach the 3 claws to install the outer lap belt anchor cover.

HINT:

Use the same procedure for the other outer lap belt anchor cover.



Hide 62332C 59.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B240010E02
0.906,1.51 1.208,1.385 false 1.208,1.385 1.292,1.385 false 0.979,0.906 1.198,1.135 0.219,0.229 10 false *2 1.292,1.292 1.51,1.521 0.219,0.229 10 false *1

Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle to install the rear door opening trim weatherstrip LH as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Mark Position


Hide 62331C 60.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67918D 61.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate LH.


Hide 67917C 62.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 67934 63.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

a.

Install the quarter scuff plate LH with the 2 bolts.


Hide 67933 64.INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 58371F 65.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

a.

Attach the 2 claws to install the rear No. 1 floor step cover.

HINT:

Use the same procedure for all the rear No. 1 floor step covers.



Hide 62212 66.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.

Attach the 2 guides and clip to install the front pillar garnish LH.


c.

Install the bolt.


d.

Attach the 2 claws to install the No. 1 front pillar garnish cover LH.


Hide 62211 67.INSTALL FRONT PILLAR GARNISH RH

a.

Remove the protective cover.


b.

Attach the clip and 3 guides to install the front pillar garnish RH.


Hide 74611F 68.INSTALL NO. 1 ASSIST GRIP

a.

Attach the 2 claws to install the No. 1 assist grip.


b.

Install the 2 bolts.


Hide 74617A 69.INSTALL ASSIST GRIP PLUG

a.

Attach the 2 claws to install the assist grip plug.

HINT:

Use the same procedure for the other assist grip plug.



Hide 62312B 70.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B240008E02
2.615,1.5 2.708,1.365 false 2.708,1.365 2.927,1.365 false 2.969,1.281 3.167,1.479 0.198,0.198 10 false *1 2.313,0.885 2.51,1.083 0.198,0.198 10 false *2

Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle to install the front door opening trim weatherstrip LH as shown in the illustration.

Text in Illustration
*1 Paint Mark
*2 Mark Position


Hide 62311B 71.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 72.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the clip and claw to install the cowl side trim board LH.


b.

Install the clip.


Hide 62111C 73.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67920 74.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

a.

Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly LH.


Hide 67910 75.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 76.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

Hide 77.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).