Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


U149674E02
3.49,0.167 3.698,0.344 0.208,0.177 10 false h1

a.

Disconnect the h1 multiplex network master switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-11 (B) - h1-12 (GND) G - W-B Power supply Always 11 to 14 V
h1-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the h1 multiplex network master switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
h1-15 (DOWN) - h1-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window regulator switch off 11 to 14 V
h1-15 (DOWN) - h1-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window switch down (Manual operation) Below 1 V
h1-18 (LED) - h1-12 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
h1-18 (LED) - h1-12 (GND) V - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
h1-20 (UP) - h1-12 (GND) L - W-B Power window motor up input Ignition switch ON, driver side power window switch off 11 to 14 V
h1-20 (UP) - h1-12 (GND) L - W-B Power window motor up input Ignition switch ON, driver side power window switch up (Manual operation) Below 1 V

If the result is not as specified, the multiplex network master switch may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


B216714E05
3.503,0.176 3.683,0.349 0.180,0.173 10 g1

a.

Disconnect the g1 power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
g1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the g1 power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
g1-6 (UP) - g1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
g1-6 (UP) - g1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
g1-8 (AUTO) - g1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
g1-8 (AUTO) - g1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
g1-8 (AUTO) - g1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
g1-4 (LED) - g1-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
g1-4 (LED) - g1-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after the ignition switch is turned off Below 1 V
g1-7 (DOWN) - g1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
g1-7 (DOWN) - g1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the power window regulator switch may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH


B216714E06
3.535,0.169 3.672,0.338 0.137,0.170 9 j1

a.

Disconnect the j1 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the j1 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
j1-6 (UP) - j1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
j1-6 (UP) - j1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
j1-8 (AUTO) - j1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
j1-8 (AUTO) - j1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
j1-8 (AUTO) - j1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
j1-4 (LED) - j1-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
j1-4 (LED) - j1-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after the ignition switch is turned off Below 1 V
j1-7 (DOWN) - j1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
j1-7 (DOWN) - j1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the power window regulator switch may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


B216714E07
3.533,0.208 3.679,0.359 0.145,0.151 10 i1

a.

Disconnect the i1 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
i1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the i1 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
i1-6 (UP) - i1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
i1-6 (UP) - i1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
i1-8 (AUTO) - i1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
i1-8 (AUTO) - i1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
i1-8 (AUTO) - i1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
i1-4 (LED) - i1-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
i1-4 (LED) - i1-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after the ignition switch is turned off Below 1 V
i1-7 (DOWN) - i1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
i1-7 (DOWN) - i1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the rear power window regulator switch may have a malfunction.



CHECK BACK DOOR POWER WINDOW REGULATOR SWITCH ASSEMBLY


B216714E09
3.531,0.208 3.682,0.359 0.151,0.151 10 f1

a.

Disconnect the f1 back door power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
f1-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the f1 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
f1-6 (UP) - f1-1 (E) P - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
f1-6 (UP) - f1-1 (E) P - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
f1-8 (AUTO) - f1-1 (E) B - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
f1-8 (AUTO) - f1-1 (E) B - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
f1-8 (AUTO) - f1-1 (E) B - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
f1-4 (ILL+) - f1-1 (E) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
f1-4 (ILL+) - f1-1 (E) V - W-B LED illumination signal Approximately 43 seconds after the ignition switch is turned off Below 1 V
f1-7 (DOWN) - f1-1 (E) R - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
f1-7 (DOWN) - f1-1 (E) R - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the rear power window regulator switch may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U149806E02
3.5,0.25 3.656,0.396 0.156,0.146 10 false I2

a.

Disconnect the I2 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I2-2 (B) - Body ground R - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the I2 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-5 (LED) - I2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
I2-5 (LED) - I2-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
I2-7 (DOWN) - I2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator master switch off 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator master switch down Below 1 V
I2-7 (DOWN) - I2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
I2-7 (DOWN) - I2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator master switch off 11 to 14 V
I2-10 (UP) - I2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator master switch up Below 1 V
I2-10 (UP) - I2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
I2-10 (UP) - I2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


U149807E02
3.479,0.25 3.698,0.396 0.219,0.146 10 false H2

a.

Disconnect the H2 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H2-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the H2 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-5 (LED) - H2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
H2-5 (LED) - H2-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
H2-7 (DOWN) - H2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
H2-7 (DOWN) - H2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
H2-7 (DOWN) - H2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
H2-7 (DOWN) - H2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
H2-7 (DOWN) - H2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
H2-10 (UP) - H2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
H2-10 (UP) - H2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
H2-10 (UP) - H2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
H2-10 (UP) - H2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
H2-10 (UP) - H2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U149808E02
3.49,0.25 3.677,0.396 0.188,0.146 10 false K2

a.

Disconnect the K2 rear power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K2-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K2 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-5 (LED) - K2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K2-5 (LED) - K2-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
K2-7 (DOWN) - K2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
K2-7 (DOWN) - K2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V
K2-7 (DOWN) - K2-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully closed 11 to 14 V
K2-7 (DOWN) - K2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window auto down function operating Below 1 V
K2-7 (DOWN) - K2-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully open 11 to 14 V
K2-10 (UP) - K2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
K2-10 (UP) - K2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
K2-10 (UP) - K2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
K2-10 (UP) - K2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
K2-10 (UP) - K2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the rear power window regulator motor may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


U149809E02
3.5,0.25 3.688,0.396 0.188,0.146 10 false J2

a.

Disconnect the J2 rear window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J2-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J2 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-5 (LED) - J2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J2-5 (LED) - J2-1 (GND) V - W-B LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
J2-7 (DOWN) - J2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
J2-7 (DOWN) - J2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
J2-7 (DOWN) - J2-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
J2-10 (UP) - J2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
J2-10 (UP) - J2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
J2-10 (UP) - J2-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the rear power window regulator motor may have a malfunction.



CHECK BACK DOOR POWER WINDOW REGULATOR MOTOR ASSEMBLY


U149810E02
3.458,0.25 3.708,0.396 0.25,0.146 10 false W9

a.

Disconnect the W9 back door power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W9-1 (GND) - Body ground LG - Body ground Ground Always Below 1 Ω
W9-2 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the W9 back door power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W9-5 (LED) - W9-1 (GND) L - LG LED illumination signal Ignition switch ON 11 to 14 V
W9-5 (LED) - W9-1 (GND) L - LG LED illumination signal Approximately 43 seconds after ignition switch turned off Below 1 V
W9-7 (DOWN) - W9-1 (GND) B - LG Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
W9-7 (DOWN) - W9-1 (GND) B - LG Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
W9-7 (DOWN) - W9-1 (GND) B - LG Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
W9-7 (DOWN) - W9-1 (GND) B - LG Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
W9-7 (DOWN) - W9-1 (GND) B - LG Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
W9-10 (UP) - W9-1 (GND) R - LG Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
W9-10 (UP) - W9-1 (GND) R - LG Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
W9-10 (UP) - W9-1 (GND) R - LG Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
W9-10 (UP) - W9-1 (GND) R - LG Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
W9-10 (UP) - W9-1 (GND) R - LG Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the back door power window regulator motor may have a malfunction.



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149717E02
1.625,1.469 1.865,1.219 1.865,1.219 1.948,1.219 false 1.625,1.823 1.865,1.583 1.865,1.583 1.948,1.583 false 1.625,2.135 1.865,1.896 1.865,1.896 1.948,1.896 false 0.896,1.573 1.104,1.729 0.208,0.156 10 false 2F 1.083,3.875 1.365,4.031 0.281,0.156 10 false F10 0.896,2.167 1.104,2.323 0.208,0.156 10 false 2D 5.865,1.49 6.073,1.646 0.208,0.156 10 false 2B 5.865,2.188 6.073,2.344 0.208,0.156 10 false 2C 1.073,2.76 1.281,2.917 0.208,0.156 10 false 2E 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.958,1.156 2.229,1.302 0.271,0.146 10 false F8 1.958,1.51 2.229,1.656 0.271,0.146 10 false F9 1.958,1.833 2.229,1.979 0.271,0.146 10 false F10 3.625,3.865 3.823,4.021 0.198,0.156 10 false F9 1.125,5.177 1.344,5.333 0.219,0.156 10 false 2F 1.885,6.406 2.104,6.563 0.219,0.156 10 false 2B 4.938,6.396 5.156,6.552 0.219,0.156 10 false 2C 3.51,7.677 3.646,7.833 0.135,0.156 10 false A 3.948,5.177 4.146,5.333 0.198,0.156 10 false 2D 5.896,5.177 6.094,5.333 0.198,0.156 10 false 2E 5.948,3.865 6.146,4.021 0.198,0.156 10 false F8

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU).


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V

If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


U149777E02
4.115,0.417 4.417,0.573 0.302,0.156 10 false W10 2.823,0.406 3.052,0.646 0.229,0.24 10 false V2

a.

Disconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V2-7 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder in neutral position Pulse generation (See waveform 1 or 2)
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder in lock position Below 1 V
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder in neutral position Pulse generation (See waveform 1 or 2)
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder in unlock position Below 1 V
V2-22 (BUP) - V2-6 (GND) P -W-B Back door power window up input Ignition switch ON, back door power window switch off Pulse generation (See waveform 3 or 4)
V2-22 (BUP) - V2-6 (GND) P - W-B Back door power window up input Ignition switch ON, back door power window switch up Below 1 V
V2-23 (BDN) - V2-6 (GND) R - W-B Back door power window up input Ignition switch ON, back door power window switch off Pulse generation (See waveform 3 or 4)
V2-23 (BDN) - V2-6 (GND) R - W-B Back door power window up input Ignition switch ON, back door power window switch down Below 1 V
W10-24 (HSW+) - W10-7 (HSW-) GR - LG Back door opener switch input Back door opener switch off Pulse generation (See waveform 5 or 6)
W10-24 (HSW+) - W10-7 (HSW-) GR - LG Back door opener switch input Back door opener switch on Below 1 V
V2-21 (AUTO) - V2-6 (GND) B - W-B Back door power window auto up or auto down input Ignition switch ON, back door power window switch off Pulse generation (See waveform 7 or 8)
V2-21 (AUTO) - V2-6 (GND) B - W-B Back door power window auto up or auto down input Ignition switch ON, back door power window switch auto up or auto down Below 1 V
V2-3 (W) - V2-12 (SGND) R - G Rear wiper reverse position switch input Ignition switch ON and rear wiper switch on or rear wiper reverse switch off Pulse generation (See waveform 9)
V2-3 (W) - V2-12 (SGND) R - G Rear wiper reverse position switch input Ignition switch ON and rear wiper switch on or rear wiper reverse switch on Pulse generation (See waveform 10)
V2-4 (P) - V2-12 (SGND) V - G Rear wiper retractable position switch input Ignition switch ON and rear wiper switch on or rear wiper retractable position switch off Pulse generation (See waveform 11)
V2-4 (P) - V2-12 (SGND) V - G Rear wiper retractable position switch input Ignition switch ON and rear wiper switch on or rear wiper retractable position switch on Pulse generation (See waveform 12)
W10-14 (BUP2) - W10-1 (E4) R - LG Back door power window regulator motor up output Ignition switch ON, back door power window regulator switch up Pulse generation (See waveform 13)
W10-13 (BDN2) - W10-1 (E4) B - LG Back door power window regulator motor down output Ignition switch ON, back door power window regulator switch down Pulse generation (See waveform 14)
W10-12 (AUT2) - W10-1 (E4) W - LG Back door power window regulator motor auto up or auto down output Ignition switch ON, back door power window auto up or auto down function operating Pulse generation (See waveform 15)

If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.


e.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol)

W10-16 (BKL) - W10-8 (KEYE)

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder in neutral position


f.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol)

W10-16 (BKL) - W10-8 (KEYE)

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder in neutral position


g.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol)

V2-22 (BUP) - V2-6 (GND)

V2-23 (BDN) - V2-6 (GND)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON, back door power window switch off


h.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol)

V2-22 (BUP) - V2-6 (GND)

V2-23 (BDN) - V2-6 (GND)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON, back door power window switch off


i.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) W10-24 (HSW+) - W10-7 (HSW-)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door opener switch off


j.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) W10-24 (HSW+) - W10-7 (HSW-)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door opener switch off


k.
B242625E01
0.112,0.975 0.444,1.131 0.332,0.156 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) V2-21 (AUTO) - V2-6 (GND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON, back door power window switch off


l.
B242626E01
0.072,0.994 0.436,1.145 0.364,0.151 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) V2-21 (AUTO) -V2-6 (GND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON, back door power window switch off


m.
B242627E01
0.095,0.96 0.436,1.129 0.341,0.170 10 GND

Using an oscilloscope, check waveform 9.

Waveform 9 (Reference)
Item Content
Terminal No. (Symbol) V2-3 (W) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON and rear wiper switch on or rear wiper reverse switch off


n.
B242628E01
0.118,0.96 0.454,1.115 0.336,0.156 10 GND

Using an oscilloscope, check waveform 10.

Waveform 10 (Reference)
Item Content
Terminal No. (Symbol) V2-3 (W) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON and rear wiper switch on or rear wiper reverse switch on


o.
B242627E01
0.095,0.96 0.436,1.129 0.341,0.170 10 GND

Using an oscilloscope, check waveform 11.

Waveform 11 (Reference)
Item Content
Terminal No. (Symbol) V2-4 (P) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON and rear wiper switch on or rear wiper retractable position switch off


p.
B242628E01
0.118,0.96 0.454,1.115 0.336,0.156 10 GND

Using an oscilloscope, check waveform 12.

Waveform 12 (Reference)
Item Content
Terminal No. (Symbol) V2-4 (P) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Ignition switch ON and rear wiper switch on or rear wiper retractable position switch on


q.
B242647E01
0.275,1.797 0.605,1.960 0.330,0.163 10 GND

Using an oscilloscope, check waveform 13.

Waveform 13 (Reference)
Item Content
Terminal No. (Symbol) W10-14 (BUP2) - W10-1 (E4)
Tool Setting 2 V/DIV., 100 ms/DIV.
Condition Ignition switch ON, back door power window regulator switch up


r.
B242647E01
0.275,1.797 0.605,1.960 0.330,0.163 10 GND

Using an oscilloscope, check waveform 14.

Waveform 14 (Reference)
Item Content
Terminal No. (Symbol) W10-13 (BDN2) - W10-1 (E4)
Tool Setting 2 V/DIV., 100 ms/DIV.
Condition Ignition switch ON, back door power window regulator switch down


s.
B242648E01
0.29,1.792 0.626,1.952 0.336,0.161 10 GND

Using an oscilloscope, check waveform 15.

Waveform 15 (Reference)
Item Content
Terminal No. (Symbol) W10-12 (AUT2) - W10-1 (E4)
Tool Setting 2 V/DIV., 100 ms/DIV.
Condition Ignition switch ON, back door power window auto up or auto down function operating