Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:

·

The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.

·

The rear power window regulator switch has a malfunction.

·

The Hall IC in the power window regulator motor has a malfunction.

·

There is an open or short in the wiring between the rear power window regulator switch and rear power window regulator motor.


WIRING DIAGRAM

B453799E01
0.531,3.417 2.135,3.635 1.604,0.219 10 false : LIN Communication Line 1.833,2.5 3.823,2.885 1.99,0.385 10 false Rear Power Window Regulator Switch Assembly LH 1.354,0.969 4.292,1.198 2.938,0.229 10 false Main Body ECU (Multiplex Network Body ECU) 2.052,1.938 2.417,2.104 0.365,0.167 10 false GND 2.958,1.927 3.323,2.094 0.365,0.167 10 false AUTO 1.833,1.813 1.979,2.01 0.146,0.198 10 false 1 3.479,1.802 3.625,2 0.146,0.198 10 false 8 1.854,2.292 2,2.49 0.146,0.198 10 false j1 5.135,1.802 5.281,2 0.146,0.198 10 false 4 5.396,1.917 5.76,2.083 0.365,0.167 10 false AUTO 5.104,2.448 5.302,2.646 0.198,0.198 10 false K2 5.083,2.625 7.073,3.01 1.99,0.385 10 false Rear Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC B2311 is output B
DTC B2312 is output C
DTC B2313 is output D



A

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

B

C

D

2.CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Check that the manual up/down function using the rear power window regulator switch can operate the rear power window regulator motor (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Manual up/down function operates.




OK

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)

NG

GO TO "Rear Power Window LH does not Operate with Rear Power Window Switch LH"

3.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)
a.

Use the Data List to check if the rear power window regulator is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF ON: Rear power window LH auto up/down switch operated
OFF: Rear power window LH switch not operated
-

OK:

On tester screen, item changes between ON and OFF according to above chart.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.
B215963E18
2.692,0.363 3.077,0.560 0.385,0.198 10 GND 0.462,1.708 0.882,1.884 0.420,0.177 10 AUTO 2.12,0.964 2.494,0.453 2.494,0.453 2.666,0.453 false 1.386,1.304 1.149,1.806 1.149,1.806 0.977,1.806 false

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW MOTOR REGULATOR LH AND BODY GROUND)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW MOTOR REGULATOR LH AND BODY GROUND)
a.

Disconnect the j1 rear power window regulator switch connector.


b.

Disconnect the K2 power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-8 (AUTO) - K2-4 (AUTO) Always Below 1 Ω
j1 (GND) - Body ground Always Below 1 Ω
j1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR