Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor is driven by operating the power window regulator switch. The power window regulator motor assembly consists of the motor and ECU.

This DTC is output when the ECU built into the regulator motor and master switch determines that the multiplex network master switch assembly or power window regulator switch assembly is stuck.

HINT:

This DTC may be stored for all the windows.


NOTICE:
·

When a power window regulator is reinstalled or replaced, the power window control system must be initialized.

·

After any door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:

1.

Close the power window by fully pulling up the power window switch and holding it in the auto up position.

2.

Open the power window by fully pushing down the power window switch.




Master Switch
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The multiplex network master switch is stuck.

·

The multiplex network master switch is held in the same position for more than 20 sec.


Multiplex network master switch

D-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The multiplex network master switch is stuck.

·

The multiplex network master switch is held in the same position for more than 20 sec.


·

Multiplex network master switch

·

Front power window regulator motor LH

·

Harness or connector



P-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The power window regulator switch is stuck.

·

The power window regulator switch is held in the same position for more than 20 sec.


·

Power window regulator switch

·

Front power window regulator motor RH

·

Harness or connector



RL-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The rear power window regulator switch LH is stuck.

·

The rear power window regulator switch LH is held in the same position for more than 20 sec.


·

Rear power window regulator switch LH

·

Rear power window regulator motor LH

·

Harness or connector



RR-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The rear power window regulator switch RH is stuck.

·

The rear power window regulator switch RH is held in the same position for more than 20 sec.


·

Rear power window regulator switch RH

·

Rear power window regulator motor RH

·

Harness or connector



WIRING DIAGRAM

for Front LH:


B242542E04
0.333,4.417 0.719,4.417 false 0.719,4.365 0.333,4.365 false 0.719,4.385 0.333,4.385 false 0.99,3.573 2.865,4.177 1.875,0.604 10 false Multiplex Network Master Switch Assembly 4.958,3.563 6.948,4.052 1.99,0.49 10 false Front Power Window Regulator Motor Assembly LH 0.885,0.917 2.563,1.292 1.677,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,1.917 5.813,2.094 0.344,0.177 10 false UP 5.198,1.813 5.385,1.99 0.188,0.177 10 false 10 5.469,2.385 5.948,2.563 0.479,0.177 10 false DOWN 1.948,1.927 2.177,2.104 0.229,0.177 10 false UP 1.719,2.365 2.198,2.542 0.479,0.177 10 false DOWN 5.271,2.25 5.375,2.427 0.104,0.177 10 false 7 2.25,1.833 2.438,2.01 0.188,0.177 10 false 20 2.25,2.26 2.427,2.438 0.177,0.177 10 false 15 0.75,4.302 2.396,4.49 1.646,0.188 10 false : LIN Communication Line 1.01,3.375 1.188,3.552 0.177,0.177 10 false h1 4.958,3.396 5.135,3.573 0.177,0.177 10 false I2


for Front RH:


B242543E10
0.333,4.479 0.719,4.479 false 0.719,4.438 0.333,4.438 false 0.719,4.458 0.333,4.458 false 2.344,3.625 4.208,3.99 1.865,0.365 10 false Power Window Regulator Switch Assembly 4.906,3.594 6.865,4.063 1.958,0.469 10 false Front Power Window Regulator Motor Assembly RH 1.927,0.969 4.146,1.344 2.219,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,1.917 5.833,2.094 0.344,0.177 10 false UP 5.188,1.792 5.375,1.969 0.188,0.177 10 false 10 5.49,2.375 5.969,2.552 0.479,0.177 10 false DOWN 5.49,2.813 5.969,2.99 0.479,0.177 10 false AUTO 3.323,1.927 3.552,2.104 0.229,0.177 10 false UP 3.094,2.365 3.573,2.542 0.479,0.177 10 false DOWN 3.135,2.802 3.552,2.979 0.417,0.177 10 false AUTO 2.604,2.802 2.958,2.979 0.354,0.177 10 false GND 2.385,2.688 2.49,2.865 0.104,0.177 10 false 1 5.271,2.25 5.375,2.427 0.104,0.177 10 false 7 5.271,2.677 5.375,2.854 0.104,0.177 10 false 4 3.667,1.771 3.854,1.948 0.188,0.177 10 false 6 3.667,2.219 3.844,2.396 0.177,0.177 10 false 7 3.667,2.677 3.781,2.854 0.115,0.177 10 false 8 0.75,4.365 2.396,4.552 1.646,0.188 10 false : LIN Communication Line 4.906,3.417 5.167,3.625 0.26,0.208 10 false H2 2.344,3.427 2.573,3.615 0.229,0.188 10 false g1


for Rear LH:


B242543E11
0.333,4.479 0.719,4.479 false 0.719,4.438 0.333,4.438 false 0.719,4.458 0.333,4.458 false 2.083,3.552 4.052,4.156 1.969,0.604 10 false Rear Power Window Regulator Switch Assembly LH 4.906,3.625 6.896,4.115 1.99,0.49 10 false Rear Power Window Regulator Motor Assembly LH 1.906,0.938 4.135,1.313 2.229,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,1.906 5.833,2.083 0.344,0.177 10 false UP 5.208,1.771 5.396,1.948 0.188,0.177 10 false 10 5.49,2.323 5.969,2.5 0.479,0.177 10 false DOWN 5.49,2.771 5.969,2.948 0.479,0.177 10 false AUTO 3.344,1.906 3.573,2.083 0.229,0.177 10 false UP 3.094,2.323 3.573,2.5 0.479,0.177 10 false DOWN 3.156,2.771 3.573,2.948 0.417,0.177 10 false AUTO 2.604,2.771 3.021,2.948 0.417,0.177 10 false GND 2.406,2.677 2.531,2.854 0.125,0.177 10 false 1 5.281,2.219 5.385,2.396 0.104,0.177 10 false 7 5.281,2.667 5.385,2.844 0.104,0.177 10 false 4 3.688,1.771 3.875,1.948 0.188,0.177 10 false 6 3.688,2.219 3.865,2.396 0.177,0.177 10 false 7 3.688,2.677 3.802,2.854 0.115,0.177 10 false 8 0.75,4.375 2.396,4.563 1.646,0.188 10 false : LIN Communication Line 4.896,3.438 5.271,3.615 0.375,0.177 10 false K2 2.083,3.385 2.531,3.542 0.448,0.156 10 false j1


for Rear RH:


B242543E12
0.333,4.479 0.719,4.479 false 0.719,4.438 0.333,4.438 false 0.719,4.458 0.333,4.458 false 2.115,3.594 4.042,3.99 1.927,0.396 10 false Rear Power Window Regulator Switch Assembly RH 4.906,3.594 6.802,3.99 1.896,0.396 10 false Rear Power Window Regulator Motor Assembly RH 1.573,0.99 4.51,1.365 2.938,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.49,1.917 5.833,2.094 0.344,0.177 10 false UP 5.208,1.771 5.396,1.948 0.188,0.177 10 false 10 5.49,2.365 5.969,2.542 0.479,0.177 10 false DOWN 5.49,2.802 5.969,2.979 0.479,0.177 10 false AUTO 3.344,1.927 3.573,2.104 0.229,0.177 10 false UP 3.094,2.365 3.573,2.542 0.479,0.177 10 false DOWN 3.156,2.802 3.573,2.979 0.417,0.177 10 false AUTO 2.604,2.802 3.021,2.979 0.417,0.177 10 false GND 5.281,2.219 5.385,2.396 0.104,0.177 10 false 7 5.281,2.667 5.385,2.844 0.104,0.177 10 false 4 3.688,1.771 3.875,1.948 0.188,0.177 10 false 6 3.688,2.219 3.865,2.396 0.177,0.177 10 false 7 3.688,2.677 3.802,2.854 0.115,0.177 10 false 8 2.396,2.677 2.51,2.854 0.115,0.177 10 false 1 0.75,4.375 2.396,4.563 1.646,0.188 10 false : LIN Communication Line 2.104,3.417 2.365,3.604 0.26,0.188 10 false i1 4.896,3.417 5.156,3.594 0.26,0.177 10 false J2


CAUTION / NOTICE / HINT

HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTCs output A
LIN communication DTCs are output B
DTC B2312 is output C



A

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

B

C

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts which the DTCs have been output from.

Result
Result Proceed to
DTC output from multiplex network master switch A
DTC output from front power window regulator motor LH B
DTC output from front power window regulator motor RH C
DTC output from rear power window regulator motor LH D
DTC output from rear power window regulator motor RH E



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

3.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH)

C

5.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH)

D

8.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH LH)

E

11.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH RH)
3.READ VALUE USING INTELLIGENT TESTER (MULTIPLEX NETWORK MASTER SWITCH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the h1 multiplex network master switch connector.


b.

Disconnect the I2 power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-20 (UP) - I2-10 (UP) Always Below 1 Ω
h1-15 (DOWN) - I2-7 (DOWN) Always Below 1 Ω
h1-20 (UP) - Body ground Always 10 kΩ or higher
h1-15 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto up/down signal / ON or OFF ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Up SW Front passenger side power window manual up signal / ON or OFF ON: Front passenger side power window manual up switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Down SW Front passenger side power window manual down signal / ON or OFF ON: Front passenger side power window manual down switch operated
OFF: Front passenger side power window regulator switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B215963E13
1.866,1.338 2.129,1.828 2.129,1.828 2.305,1.828 false 2.335,1.733 2.554,1.893 0.218,0.159 10 UP 2.765,0.358 3.115,0.518 0.350,0.159 10 GND 1.605,1.338 1.341,1.828 1.341,1.828 1.165,1.828 false 0.576,1.733 1.045,1.893 0.468,0.159 10 DOWN 0.198,0.788 0.625,0.947 0.427,0.159 10 AUTO 1.308,1.251 0.896,0.883 0.896,0.883 0.733,0.883 false 2.128,0.991 2.563,0.457 2.563,0.457 2.735,0.457 false

Remove the power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual up operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the g1 power window regulator switch connector.


b.

Disconnect the H2 power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-6 (UP) - H2-10 (UP) Always Below 1 Ω
g1-7 (DOWN) - H2-7 (DOWN) Always Below 1 Ω
g1-8 (AUTO) - H2-4 (AUTO) Always Below 1 Ω
g1-6 (UP) - Body ground Always 10 kΩ or higher
g1-7 (DOWN) - Body ground Always 10 kΩ or higher
g1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH LH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF ON: Rear power window LH auto up/down switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Up SW Rear power window LH manual up signal / ON or OFF ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW Rear power window LH manual down signal / ON or OFF ON: Rear power window LH manual down switch operated
OFF: Rear power window LH switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

9.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
9.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.
B215963E13
1.866,1.338 2.129,1.828 2.129,1.828 2.305,1.828 false 2.335,1.733 2.554,1.893 0.218,0.159 10 UP 2.765,0.358 3.115,0.518 0.350,0.159 10 GND 1.605,1.338 1.341,1.828 1.341,1.828 1.165,1.828 false 0.576,1.733 1.045,1.893 0.468,0.159 10 DOWN 0.198,0.788 0.625,0.947 0.427,0.159 10 AUTO 1.308,1.251 0.896,0.883 0.896,0.883 0.733,0.883 false 2.128,0.991 2.563,0.457 2.563,0.457 2.735,0.457 false

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual up operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

10.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the j1 rear power window regulator switch connector.


b.

Disconnect the K2 rear power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-6 (UP) - K2-10 (UP) Always Below 1 Ω
j1-7 (DOWN) - K2-7 (DOWN) Always Below 1 Ω
j1-8 (AUTO) - K2-4 (AUTO) Always Below 1 Ω
j1-6 (UP) - Body ground Always 10 kΩ or higher
j1-7 (DOWN) - Body ground Always 10 kΩ or higher
j1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH RH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear power window RH auto up/down signal / ON or OFF ON: Rear power window RH auto up/down switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Up SW Rear power window RH manual up signal / ON or OFF ON: Rear power window RH manual up switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Down SW Rear power window RH manual down signal / ON or OFF ON: Rear power window RH manual down switch operated
OFF: Rear power window RH switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

12.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
12.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B215963E13
1.866,1.338 2.129,1.828 2.129,1.828 2.305,1.828 false 2.335,1.733 2.554,1.893 0.218,0.159 10 UP 2.765,0.358 3.115,0.518 0.350,0.159 10 GND 1.605,1.338 1.341,1.828 1.341,1.828 1.165,1.828 false 0.576,1.733 1.045,1.893 0.468,0.159 10 DOWN 0.198,0.788 0.625,0.947 0.427,0.159 10 AUTO 1.308,1.251 0.896,0.883 0.896,0.883 0.733,0.883 false 2.128,0.991 2.563,0.457 2.563,0.457 2.735,0.457 false

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual up operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the i1 rear power window regulator switch connector.


b.

Disconnect the J2 rear power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-6 (UP) - J2-10 (UP) Always Below 1 Ω
i1-7 (DOWN) - J2-7 (DOWN) Always Below 1 Ω
i1-8 (AUTO) - J2-4 (AUTO) Always Below 1 Ω
i1-6 (UP) - Body ground Always 10 kΩ or higher
i1-7 (DOWN) - Body ground Always 10 kΩ or higher
i1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR