The power window regulator motor is operated by the multiplex network master switch or power window regulator switch. The power window regulator motor assembly has motor and ECU functions.
This DTC is stored when the power window regulator motor has a malfunction, or the ECU built into the regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
DTC B2311 can be stored in each power window regulator motor (power window ECU).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: 1.
Power window regulator motor assembly malfunctions. 2.
ECU in the power window regulator motor determines that the fully closed window position has deviated approx. 20 mm (0.787 in.) or more from the normal position. |
Front power window regulator motor LH |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: 1.
Power window regulator motor malfunctions. 2.
ECU in the power window regulator motor determines that the fully closed window position has deviated approx. 20 mm (0.787 in.) or more from the normal position. |
Front power window regulator motor RH |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: 1.
Power window regulator motor malfunctions. 2.
ECU in the power window regulator motor determines that the fully closed window position has deviated approx. 20 mm (0.787 in.) or more from the normal position. |
Rear power window regulator motor LH |
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2311 | Either condition is met: 1.
Power window regulator motor malfunctions. 2.
ECU in the power window regulator motor determines that the fully closed window position has deviated approx. 20 mm (0.787 in.) or more from the normal position. |
Rear power window regulator motor RH |
When a power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
After any door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
Close the power window by fully pulling up the multiplex network master switch or power window regulator switch and holding it in the auto up position.
Open the power window by fully pushing down the switch.
Select the Active Test, use the intelligent tester to generate a control command, and then check that each door window regulator operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Driver side power window | OFF/UP/DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Passenger side power window | OFF/UP/DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Rear LH side power window | OFF/UP/DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Rear RH side power window | OFF/UP/DOWN | - |
Each power window regulator motor operates.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Front power window LH) | B |
| NG (Front power window RH) | C |
| NG (Rear power window LH) | D |
| NG (Rear power window RH) | E |
A
B
C
D
E
Initialize the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check that each power window operates normally by opening and closing the window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Each power window operates normally.
NEXT
Check that the power window components are installed correctly.
Power window components are installed correctly.
If the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch was ON, or the motor being overheated.
OK
NG