Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274171 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 62786C 1.INSTALL QUARTER WINDOW GLASS SPACER LH

B241748E02
1.427,1.427 1.031,1.615 false 0.615,0.823 0.813,1.021 0.198,0.198 10 false a 2.135,0.24 2.396,0.5 0.26,0.26 10 false b 0.042,0.063 0.219,0.25 0.177,0.188 10 true *a 0.865,1.573 1.042,1.76 0.177,0.188 10 false *1

a.

Apply Primer G to the window where the spacer will be installed.

Standard:
Area Specified Condition
a 32.1 mm (1.26 in.)
b 24.8 mm (0.976 in.)


Text in Illustration
*1 Spacer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new spacer. Install the spacer to the quarter window at the location shown in the illustration.


Hide 62764K 2.INSTALL UPPER QUARTER WINDOW GLASS RETAINER

B241749E02
2.802,1.396 2.99,1.396 false 0.073,0.063 0.323,0.292 0.25,0.229 10 false *a 3.01,1.333 3.292,1.573 0.281,0.24 10 false *1 1.813,0.115 1.958,0.292 0.146,0.177 10 false a 1.417,0.969 1.708,1.26 0.292,0.292 10 false b

a.

Apply Primer G to the window where the retainer will be installed.

Standard:
Area Specified Condition
a 3.8 mm (0.150 in.)
b 27.9 mm (1.10 in.)


Text in Illustration
*1 Retainer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new retainer. Install the retainer to the quarter window at the location shown in the illustration.


Hide 62762J 3.INSTALL FRONT QUARTER WINDOW GLASS RETAINER LH

B241750E01
0.379,0.962 0.579,1.134 0.200,0.172 10 a 1.534,1.882 1.693,2.066 0.159,0.185 10 b 0.033,0 0.291,0.290 0.258,0.290 10 *a 2.308,0.513 2.518,0.737 0.210,0.224 10 *1 2.042,0.623 2.297,0.623 false

a.

Apply Primer G to the window where the retainer will be installed.

Standard:
Area Specified Condition
a 18.9 mm (0.744 in.)
b 7.0 mm (0.276 in.)


Text in Illustration
*1 Retainer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new retainer. Install the retainer to the quarter window at the location shown in the illustration.


Hide 62766 4.INSTALL LOWER QUARTER WINDOW GLASS RETAINER LH

B241751E02
2.573,1.052 2.844,1.052 false 0.063,0.052 0.292,0.25 0.229,0.198 10 false *a 2.875,0.979 3.156,1.198 0.281,0.219 10 false *1 1.927,0.406 2.104,0.552 0.177,0.146 10 false a 1.198,1.26 1.406,1.469 0.208,0.208 10 false b

a.

Apply Primer G to the window where the retainer will be installed.

Standard:
Area Specified Condition
a 15.1 mm (0.594 in.)
b 17.1 mm (0.673 in.)


Text in Illustration
*1 Retainer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new retainer. Install the retainer to the quarter window at the location shown in the illustration.


Hide 62785A 5.INSTALL QUARTER WINDOW GLASS SPACER

B241752E01
0.054,0 0.264,0.178 0.210,0.178 10 *a 2.478,0.749 2.687,0.928 0.210,0.178 10 *1 2.112,0.849 2.435,0.849 false

a.

Apply Primer G to the window where the spacer will be installed.

Text in Illustration
*1 Spacer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new spacer. Install the spacer to the quarter window at the location shown in the illustration.


Hide 62740B 6.INSTALL REAR QUARTER WINDOW ASSEMBLY LH

B241744E02
2.542,1.167 2.313,1.01 false 2.531,2.25 2.125,1.854 false 2.458,3.646 2.802,3.698 false 2.469,2.344 2.052,2.177 false 1.042,2.406 1.313,2.896 false 2.729,0.271 2.927,0.479 0.198,0.208 10 false *a 2.729,1.406 2.927,1.615 0.198,0.208 10 false *b 1.948,1.708 2.146,1.917 0.198,0.208 10 false *1 0.906,2.229 1.104,2.438 0.198,0.208 10 false *1 2.833,3.635 3.031,3.844 0.198,0.208 10 false *c 2.167,0.875 2.365,1.083 0.198,0.208 10 false *1 1.875,2.052 2.073,2.26 0.198,0.208 10 false *2

a.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


b.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B241745E02
2.948,1.729 3.344,2.021 false 4.698,2.208 5.125,1.917 false 6.427,0.885 6.021,0.583 false 4.719,0.896 5.344,0.698 5.344,0.698 4.906,0.896 false 0.063,0 0.385,0.313 0.323,0.313 10 false *a 0.854,2.51 1.198,2.719 0.344,0.208 10 false *1 3.406,1.969 3.677,2.208 0.271,0.24 10 false *b 2.156,0.427 2.344,0.615 0.188,0.188 10 false A 2.146,0.854 2.333,1.042 0.188,0.188 10 false A 1.177,0.583 1.354,0.833 0.177,0.25 10 false B 1.458,0.844 1.635,1.094 0.177,0.25 10 false B 1.583,1.729 1.719,1.958 0.135,0.229 10 false C 1.583,2.146 1.719,2.375 0.135,0.229 10 false C 3.438,1.302 3.573,1.531 0.135,0.229 10 false C 3.115,1.031 3.25,1.26 0.135,0.229 10 false C 5.958,0.063 6.521,0.281 0.563,0.219 10 false A - A 4.344,1.406 4.906,1.625 0.563,0.219 10 false C - C 4.333,0.052 4.896,0.271 0.563,0.219 10 false B - B 4.448,0.25 4.604,0.406 0.156,0.156 10 false a 5.073,0.531 5.333,0.781 0.26,0.25 10 false b 6.531,0.344 6.76,0.563 0.229,0.219 10 false a 4.5,1.625 4.698,1.823 0.198,0.198 10 false a 4.531,1.073 4.656,1.26 0.125,0.188 10 false c 4.938,1.073 5.063,1.26 0.125,0.188 10 false c 6.302,1.156 6.427,1.344 0.125,0.188 10 false c 6.521,1.156 6.646,1.344 0.125,0.188 10 false c 4.552,2.479 4.677,2.667 0.125,0.188 10 false c 4.771,2.469 4.896,2.656 0.125,0.188 10 false c 5.375,0.573 5.646,0.813 0.271,0.24 10 false *b 5.833,0.417 6.104,0.656 0.271,0.24 10 false *b 5.167,1.771 5.438,2.01 0.271,0.24 10 false *b

Text in Illustration
*1 Primer G - -
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 13.5 mm (0.531 in.)
b 4.0 mm (0.157 in.)
c 10.0 mm (0.394 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the quarter window glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

B241746E02
0.227,3.439 0.382,3.609 0.155,0.169 10 a 0.685,2.998 0.865,3.217 0.181,0.219 10 b 2.2,0.721 2.430,0.951 0.230,0.230 10 a 2.672,0.878 2.865,1.061 0.193,0.184 10 b 2.097,1.408 2.327,1.656 0.230,0.248 10 A 2.097,1.833 2.327,2.081 0.230,0.248 10 A 1.471,1.838 1.657,2.047 0.186,0.209 10 B 1.189,1.555 1.375,1.764 0.186,0.209 10 B 1.574,2.685 1.799,2.949 0.225,0.264 10 C 1.574,3.138 1.799,3.402 0.225,0.264 10 C 3.092,2.049 3.317,2.313 0.225,0.264 10 C 3.447,2.292 3.672,2.556 0.225,0.264 10 C 2.931,2.746 3.297,3.052 false 0.098,0.054 0.342,0.321 0.243,0.268 10 *a 5.274,0.526 5.459,0.736 0.185,0.210 10 c 4.874,1.683 5.080,1.889 0.206,0.206 10 c 5.495,1.903 5.751,2.118 0.257,0.215 10 b 4.884,2.798 5.074,2.988 0.190,0.190 10 c 5.074,3.556 5.358,3.272 false 5.259,2.384 5.539,2.664 5.539,2.664 5.074,2.384 false 5.173,1.231 5.428,1.486 false 5.434,1.469 5.705,1.710 0.270,0.241 10 *b 5.588,2.65 5.859,2.891 0.270,0.241 10 *b 5.414,3.132 5.685,3.373 0.270,0.241 10 *b 3.33,2.996 3.601,3.237 0.270,0.241 10 *b 4.612,0.554 5.039,0.752 0.427,0.198 10 A - A 4.612,1.519 5.087,1.759 0.475,0.239 10 B - B 4.612,2.61 5.067,2.801 0.455,0.191 10 C - C

Text in Illustration
*1 Adhesive - -
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 13.5 mm (0.531 in.)


HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the quarter window glass as shown in the illustration.



d.

Install the quarter window glass to the vehicle body.

B241747

i.

Attach the 3 retainers and 2 spacers to install the quarter window assembly LH.

NOTICE:

Allow the primer to dry for 3 minutes or more.



ii.

Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check the clearance between the body and glass.




iii.

Lightly press the front surface of the glass to ensure a close fit.


iv.
BO03986E16
1.094,1.646 1.594,1.813 false 1.625,1.719 1.802,1.917 0.177,0.198 10 false *1

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours


Text in Illustration
*1 Adhesive



Hide 62740B 7.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 62440 8.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

B242802E01
2,2.199 2.192,2.382 0.193,0.184 10 *1 1.65,2.605 1.833,2.279 1.833,2.279 1.945,2.279 false

a.

Install a new clip A to the roof side rail garnish.

Text in Illustration
*1 New Clip


b.

Attach the 3 clips to install the roof side rail garnish.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

Install the roof headlining assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).