Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS › from 2013.08
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274171 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62786C 1.INSTALL QUARTER WINDOW GLASS SPACER LH

a.
B241748E02
1.427,1.427 1.031,1.615 false 0.615,0.823 0.813,1.021 0.198,0.198 10 false a 2.135,0.24 2.396,0.5 0.26,0.26 10 false b 0.042,0.063 0.219,0.25 0.177,0.188 10 true *a 0.865,1.573 1.042,1.76 0.177,0.188 10 false *1

Apply Primer G to the rear quarter window assembly LH where the quarter window glass spacer LH will be installed.

Standard:
Area Specified Condition
a 32.1 mm (1.26 in.)
b 24.8 mm (0.976 in.)


Text in Illustration
*1 Quarter Window Glass Spacer LH
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new quarter window glass spacer LH. Install the quarter window glass spacer LH to the rear quarter window assembly LH at the location shown in the illustration.


Hide 62764K 2.INSTALL UPPER QUARTER WINDOW GLASS RETAINER

a.
B241749E02
2.802,1.396 2.99,1.396 false 0.073,0.063 0.323,0.292 0.25,0.229 10 false *a 3.01,1.333 3.292,1.573 0.281,0.24 10 false *1 1.813,0.115 1.958,0.292 0.146,0.177 10 false a 1.417,0.969 1.708,1.26 0.292,0.292 10 false b

Apply Primer G to the rear quarter window assembly where the upper quarter window glass retainer will be installed.

Standard:
Area Specified Condition
a 3.8 mm (0.150 in.)
b 27.9 mm (1.10 in.)


Text in Illustration
*1 Upper Quarter Window Glass Retainer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new upper quarter window glass retainer. Install the upper quarter window glass retainer to the rear quarter window assembly LH at the location shown in the illustration.


Hide 62762J 3.INSTALL FRONT QUARTER WINDOW GLASS RETAINER LH

a.
B241750E01
0.379,0.962 0.579,1.134 0.200,0.172 10 a 1.534,1.882 1.693,2.066 0.159,0.185 10 b 0.033,0 0.291,0.290 0.258,0.290 10 *a 2.308,0.513 2.518,0.737 0.210,0.224 10 *1 2.042,0.623 2.297,0.623 false

Apply Primer G to the rear quarter window assembly LH where the front quarter window glass retainer LH will be installed.

Standard:
Area Specified Condition
a 18.9 mm (0.744 in.)
b 7.0 mm (0.276 in.)


Text in Illustration
*1 Front Quarter Window Glass Retainer LH
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new front quarter window glass retainer LH. Install the front quarter window glass retainer LH to the rear quarter window assembly LH at the location shown in the illustration.


Hide 62766 4.INSTALL LOWER QUARTER WINDOW GLASS RETAINER LH

a.
B241751E02
2.573,1.052 2.844,1.052 false 0.063,0.052 0.292,0.25 0.229,0.198 10 false *a 2.875,0.979 3.156,1.198 0.281,0.219 10 false *1 1.927,0.406 2.104,0.552 0.177,0.146 10 false a 1.198,1.26 1.406,1.469 0.208,0.208 10 false b

Apply Primer G to the rear quarter window assembly LH where the lower quarter window glass retainer LH will be installed.

Standard:
Area Specified Condition
a 15.1 mm (0.594 in.)
b 17.1 mm (0.673 in.)


Text in Illustration
*1 Lower Quarter Window Glass Retainer LH
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new lower quarter window glass retainer LH. Install the lower quarter window glass retainer LH to the rear quarter window assembly LH at the location shown in the illustration.


Hide 62785A 5.INSTALL QUARTER WINDOW GLASS SPACER

a.
B241752E01
0.054,0 0.264,0.178 0.210,0.178 10 *a 2.478,0.749 2.687,0.928 0.210,0.178 10 *1 2.112,0.849 2.435,0.849 false

Apply Primer G to the rear quarter window assembly LH where the quarter window glass spacer will be installed.

Text in Illustration
*1 Quarter Window Glass Spacer
*a Backside

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.

Remove the peeling paper from a new quarter window glass spacer. Install the quarter window glass spacer to the rear quarter window assembly LH at the location shown in the illustration.


Hide 62740B 6.INSTALL REAR QUARTER WINDOW ASSEMBLY LH

a.
B354354E01
2.452,0.269 2.655,0.441 0.203,0.172 10 *a 2.417,1.653 2.620,1.824 0.203,0.172 10 *b

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

Text in Illustration
*a Correct
*b Incorrect
V100145

Primer M
V100155

Adhesive

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the rear quarter window assembly LH.

B354355E02
2.917,1.771 3.313,2.167 true 4.677,0.906 5.25,0.688 5.25,0.688 4.865,0.906 true 4.688,2.208 5.104,1.813 true 6.427,0.885 6.073,0.635 true 0.073,0.073 0.26,0.24 0.188,0.167 10 false *a 2.146,0.385 2.292,0.542 0.146,0.156 10 false A 2.146,0.844 2.292,1 0.146,0.156 10 false A 1.177,0.552 1.323,0.708 0.146,0.156 10 false B 1.448,0.823 1.594,0.979 0.146,0.156 10 false B 1.594,1.729 1.74,1.885 0.146,0.156 10 false C 3.094,1.021 3.24,1.177 0.146,0.156 10 false C 3.427,1.281 3.573,1.438 0.146,0.156 10 false C 1.594,2.156 1.74,2.313 0.146,0.156 10 false C 3.365,2.146 3.552,2.313 0.188,0.167 10 false *b 5.125,1.635 5.313,1.802 0.188,0.167 10 false *b 5.26,0.563 5.448,0.729 0.188,0.167 10 false *b 5.896,0.479 6.083,0.646 0.188,0.167 10 false *b 4.49,1.646 4.604,1.813 0.115,0.167 10 false a 6.542,0.354 6.656,0.521 0.115,0.167 10 false a 4.458,0.271 4.573,0.438 0.115,0.167 10 false a 4.708,0.458 4.823,0.625 0.115,0.167 10 false b 4.552,2.479 4.667,2.646 0.115,0.167 10 false c 4.76,2.479 4.875,2.646 0.115,0.167 10 false c 6.281,1.146 6.396,1.313 0.115,0.167 10 false c 6.521,1.146 6.635,1.313 0.115,0.167 10 false c 4.51,1.094 4.625,1.26 0.115,0.167 10 false c 4.917,1.094 5.031,1.26 0.115,0.167 10 false c 5.938,0.042 6.292,0.208 0.354,0.167 10 false A - A 4.323,0.042 4.677,0.208 0.354,0.167 10 false B - B 4.323,1.448 4.677,1.615 0.354,0.167 10 false C - C

Text in Illustration
*a Backside *b Adhesive Center Line
V100155

Primer G - -

Standard:
Area Specified Condition
a 13.5 mm (0.531 in.)
b 8.0 mm (0.315 in.)
c 10.0 mm (0.394 in.)


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



c.

Apply adhesive to the rear quarter window assembly LH.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration.

B241746E03
2.938,2.76 3.313,3.063 true 5.063,3.563 5.344,3.281 true 5.24,2.406 5.521,2.688 5.521,2.688 5.052,2.406 true 5.156,1.271 5.406,1.531 true 0.229,3.438 0.385,3.604 0.156,0.167 10 false a 0.688,3 0.865,3.219 0.177,0.219 10 false b 2.198,0.719 2.427,0.948 0.229,0.229 10 false a 2.677,0.875 2.875,1.063 0.198,0.188 10 false b 2.094,1.406 2.323,1.656 0.229,0.25 10 false A 2.094,1.833 2.323,2.083 0.229,0.25 10 false A 1.469,1.833 1.656,2.042 0.188,0.208 10 false B 1.188,1.552 1.375,1.76 0.188,0.208 10 false B 1.573,2.688 1.802,2.948 0.229,0.26 10 false C 1.573,3.135 1.802,3.396 0.229,0.26 10 false C 3.094,2.052 3.323,2.313 0.229,0.26 10 false C 3.448,2.292 3.677,2.552 0.229,0.26 10 false C 0.094,0.052 0.333,0.323 0.24,0.271 10 false *a 5.271,0.521 5.458,0.729 0.188,0.208 10 false c 4.875,1.688 5.083,1.896 0.208,0.208 10 false c 5.5,1.906 5.76,2.125 0.26,0.219 10 false b 4.885,2.802 5.073,2.99 0.188,0.188 10 false c 5.458,1.49 5.729,1.729 0.271,0.24 10 false *b 5.573,2.667 5.844,2.906 0.271,0.24 10 false *b 5.385,3.135 5.656,3.375 0.271,0.24 10 false *b 3.354,3.01 3.625,3.25 0.271,0.24 10 false *b 4.615,0.552 5.042,0.75 0.427,0.198 10 false A - A 4.615,1.521 5.094,1.76 0.479,0.24 10 false B - B 4.615,2.615 5.073,2.802 0.458,0.188 10 false C - C

Text in Illustration
*a Backside *b Adhesive Center Line
V100155

Adhesive - -

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 13.5 mm (0.531 in.)


HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the rear quarter window assembly LH as shown in the illustration.



d.

Install the rear quarter window assembly LH to the vehicle body.

i.

Attach the 3 retainers and 2 spacers to install the rear quarter window assembly LH.

B241747E02
1.677,0.708 1.49,0.844 false 2.031,2.365 2.083,2.125 false 4.552,2.469 4.583,2.208 false 6.115,1.833 6.042,1.615 true 5.063,0.969 4.792,0.917 false 1.948,2.385 2.146,2.552 0.198,0.167 10 false *1 4.469,2.49 4.667,2.656 0.198,0.167 10 false *1 5.083,0.927 5.281,1.094 0.198,0.167 10 false *1 6.094,1.865 6.292,2.031 0.198,0.167 10 false *2 1.677,0.563 1.875,0.729 0.198,0.167 10 false *2

Text in Illustration
*1 Retainer *2 Spacer

NOTICE:

Allow the primer to dry for 3 minutes or more.



ii.

Hold the rear quarter window assembly LH in place securely with protective tape or equivalent until the adhesive hardens.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check the clearance between the body and glass.




iii.

Lightly press the front surface of the glass to ensure a close fit.


iv.
BO03986E18
0.979,1.635 1.646,1.833 false 1.698,1.74 1.885,1.938 0.188,0.198 10 false *1

Using a scraper, remove any excess or protruding adhesive.

Text in Illustration
*1 Adhesive

NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 7.CONNECT WINDOW GLASS ANTENNA WIRE

a.

Connect the window glass antenna connector (for LH side).


b.

Connect the window glass antenna connector (for RH side).


Hide 62740B 8.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 62440 9.INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.
B242802E01
2,2.199 2.192,2.382 0.193,0.184 10 *1 1.65,2.605 1.833,2.279 1.833,2.279 1.945,2.279 false

Install new 3 clips to the roof side rail garnish assembly LH.

Text in Illustration
*1 Clip


b.

Attach the 3 clips to install the roof side rail garnish assembly LH.


Hide 63310 10.INSTALL ROOF HEADLINING ASSEMBLY