Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274171 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 63310 1.REMOVE ROOF HEADLINING ASSEMBLY

a.

Remove the roof headlining assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 62440 2.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

B241684E01
1.71,2.768 1.907,2.959 0.197,0.191 10 *1 2.197,2.48 2.037,2.854 2.037,2.854 1.933,2.854 false

a.

Detach the 3 clips.


b.

Cut off clip A.


c.

Detach the 3 guides and remove the roof side rail garnish.


d.

Remove clip A from the vehicle body.

Text in Illustration
*1 Clip A


Hide 62740B 3.REMOVE REAR QUARTER WINDOW ASSEMBLY LH

B241743E02
1.219,1.188 0.656,1.542 false 1.729,3 1.813,3.229 false 0.5,1.5 0.781,1.698 0.281,0.198 10 false *1 1.75,3.229 2.01,3.448 0.26,0.219 10 false *2

HINT:

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


NOTICE:

When separating the quarter window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.


a.

From the interior, insert a piano wire between the vehicle body and quarter window glass as shown in the illustration.

Text in Illustration
*1 Protective Tape
*2 Wire


b.
B242807

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


c.

Cut through the adhesive by pulling the piano wire around the quarter window glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the quarter window glass.



d.

Using suction cups, remove the quarter window glass.


Hide 4.CLEAN VEHICLE BODY

B106081E23
0.49,1.313 0.771,0.719 0.771,0.719 0.948,0.719 true 2.271,1.438 2.552,0.74 2.552,0.74 2.719,0.74 true 2.427,1.615 2.427,1.792 false 0.813,1.563 0.813,1.75 false 1.01,0.646 1.25,0.844 0.24,0.198 10 false *1 2.771,0.677 3.01,0.875 0.24,0.198 10 false *1 0.719,1.76 0.958,1.958 0.24,0.198 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2

a.

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Adhesive
*2 Vehicle Body

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.