Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056165 INTERIOR PANELS / TRIM _0274158 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 2.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

a.

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY>REMOVAL).


Hide 67920 3.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B240006E03
1.948,2.688 2.021,3.115 true 2.021,3.115 2.125,3.115 false 2.219,2.688 2.531,3.24 true 2.531,3.24 2.604,3.24 false 2.135,3.031 2.323,3.25 0.188,0.219 10 false *1 2.615,3.156 2.802,3.375 0.188,0.219 10 false *1

a.

Put protective tape around the door scuff plate.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

HINT:

Tape the screwdriver tip before use.



Hide 67910 4.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

B238734

a.

Remove the clip.


b.

Detach the clip and claw and remove the cowl side trim board.


Hide 62111C 6.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B240007

a.

Remove the front door opening trim weatherstrip.


Hide 62311B 8.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 74617A 9.REMOVE ASSIST GRIP PLUG

B238813E03
1.813,1.208 2.573,1.667 true 2.573,1.667 2.677,1.667 false 2.698,1.573 2.875,1.938 0.177,0.365 10 false *1

HINT:

Use the same procedure for the other assist grip plug.


a.

Using a screwdriver, detach the 2 claws and remove the assist grip plug.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 74611F 10.REMOVE NO. 1 ASSIST GRIP

B238814

a.

Remove the 2 bolts.


b.

Detach the 2 claws and remove the No. 1 assist grip.


Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH

B240012E01
0.876,2.218 1.091,2.408 0.215,0.191 10 *1 0.615,2.739 0.821,2.315 false 0.821,2.315 0.907,2.315 false

a.

Detach the 2 clips.


b.

Cut off clip A.


c.

Detach the 2 guides and remove the front pillar garnish.


d.

Remove clip A from the vehicle body.

Text in Illustration
*1 Clip A


e.
B240015E02
0.604,1.469 0.76,1.469 false 0.76,1.469 1.073,0.969 true 1.875,0.979 2.302,0.625 false 2.302,0.625 2.469,0.625 false 1.865,2.865 2.646,2.052 true 2.646,2.052 2.75,2.052 false 0.448,1.385 0.698,1.677 0.25,0.292 10 false *1 2.458,0.521 2.708,0.813 0.25,0.292 10 false *2 2.802,1.969 3.052,2.26 0.25,0.292 10 false *3

Protect the curtain shield airbag assembly.

i.

Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


Text in Illustration
*1 Curtain Shield Airbag Assembly
*2 Adhesive Tape
*3 Protective Cover



Hide 62211 12.REMOVE FRONT PILLAR GARNISH RH

B240014

a.

Detach the clip and 3 guides and remove the front pillar garnish.


b.
B240016E02
0.927,0.688 1.042,0.688 false 1.042,0.688 1.5,1.219 false 0.51,1.5 0.635,1.5 false 0.635,1.5 1.271,2.615 true 1.979,1.635 2.677,2.302 true 2.677,2.302 2.823,2.302 false 2.823,2.198 3.083,2.438 0.26,0.24 10 false *1 0.771,0.604 1.031,0.844 0.26,0.24 10 false *2 0.333,1.417 0.594,1.656 0.26,0.24 10 false *3

Protect the curtain shield airbag assembly.

i.

Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


Text in Illustration
*1 Curtain Shield Airbag Assembly
*2 Adhesive Tape
*3 Protective Cover



Hide 58371F 13.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

B238730E06
1.646,1.26 2.042,1.51 true 2.042,1.51 2.146,1.51 false 2.146,1.417 2.375,1.604 0.229,0.188 10 true *1

HINT:

Use the same procedure for all rear No. 1 floor step covers.


a.

Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 67934 14.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

B238731

a.

Remove the 2 bolts and quarter scuff plate.


Hide 67933 15.REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 67918D 16.REMOVE REAR DOOR SCUFF PLATE LH

B240011E03
1.698,2.719 1.917,3.135 false 1.917,3.135 2.021,3.135 false 2.333,2.688 2.25,3.188 false 2.25,3.188 2.354,3.188 false 2.365,3.094 2.573,3.396 0.208,0.302 10 false *1 2.031,3.063 2.24,3.365 0.208,0.302 10 false *1

a.

Put protective tape around the rear door scuff plate.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.


Hide 67917C 17.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62332C 18.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B240009

a.

Remove the rear door opening trim weatherstrip.


Hide 62331C 19.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 73233 20.REMOVE OUTER LAP BELT ANCHOR COVER

B238735

HINT:

Use the same procedure for the other outer lap belt anchor cover.


a.

Detach the 3 claws and remove the outer lap belt anchor cover.


Hide 62414A 21.REMOVE LOWER CENTER PILLAR GARNISH LH

B238736

a.

Remove the bolt and disconnect the front seat outer belt floor anchor.


b.
B238737

Detach the 4 claws and 2 clips and remove the lower center pillar garnish.


Hide 62413A 22.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62412 23.REMOVE CENTER PILLAR GARNISH LH

B240017

a.

Move the front shoulder belt anchor adjuster to the lowest position.


b.

Remove the bolt.


c.

Detach the 2 clips and 2 guides.


d.

Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.


Hide 62411 24.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 64721B 25.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

B240044

HINT:

Use the same procedure for the other No. 1 luggage compartment trim cover.


a.

Detach the 4 claws and open the cover.


b.
B240045E02
2.083,1.156 2.594,0.948 true 2.594,0.948 2.719,0.948 false 2.729,0.865 2.958,1.021 0.229,0.156 10 false *1

Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker


Hide 58401A 26.REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

B240046

a.

Detach the clip and remove the No. 1 deck board.


Hide 64722B 27.REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)

B240048

HINT:

Use the same procedure for all No. 2 luggage compartment trim covers.


a.

Detach the 2 claws and open the cover.


b.
B240049E02
2.073,1.021 2.625,0.552 true 2.625,0.552 2.781,0.552 false 2.771,0.427 3,0.625 0.229,0.198 10 false *1

Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker


Hide 58408D 28.REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

B240064

a.

Detach the 2 clips and 2 guides and remove the No. 2 deck board.


Hide 58480B 29.REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

B240065

a.

Detach the 3 clips and remove the rear No. 2 floor board.


Hide 58704A 30.REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

B240062E02
2.802,1 3.135,0.219 true 3.135,0.219 2.979,0.219 false 2.813,0.146 3.031,0.438 0.219,0.292 10 false *1

a.

Using a screwdriver, detach the 4 clips and 2 guides and remove the luggage compartment side cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 58703A 31.REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:

Use the same procedure described for the LH side.


Hide 58410R 32.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

B240063

a.

Remove the 8 bolts.


b.

Detach the 2 guides and remove the deck board.


Hide 58306A 33.REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

B240067

a.

Remove the 2 bolts, 4 nuts and inner floor side rail.


Hide 58574A 34.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B240050

a.

Detach the 5 clips and remove the rear floor mat rear support plate.


Hide 58570C 35.REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

B240047

a.

Detach the 4 claws and remove the rear floor carpet.


Hide 36.REMOVE REAR FLOOR CARPET ASSEMBLY (w/ Deck Board)

a.

Detach the 4 claws and remove the rear floor carpet.


Hide 73233A 37.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

B240053

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


a.

Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.


Hide 64725J 38.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

B181695

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook.


a.

Remove the luggage compartment trim hook by turning it clockwise.


Hide 64713F 39.REMOVE FRONT DECK SIDE TRIM COVER LH

B240051E03
1.615,1.479 2.167,1.844 false 2.167,1.844 2.333,1.844 false 2.333,1.75 2.615,1.917 0.281,0.167 10 false *1

HINT:

Use the same procedure for the other front deck side trim cover.


a.

Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 64712F 40.REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 64740C 41.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.
B240054

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.

Remove the 3 bolts and 2 screws.


iii.

Detach the 7 clips, 5 claws and 2 guides.

B240058


iv.
B238756

Detach the 6 claws and 2 guides, pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.



b.

w/ Rear No. 2 Seat:

i.
B240054

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B240052

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 3 bolts and 2 screws.


iv.

Detach the 7 clips, 5 claws and 2 guides and remove the deck trim side panel.

B240060



Hide 64730B 42.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat:

i.
B240057

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.

Remove the 3 bolts and screws.


iii.

Detach the 7 clips, 5 claws and 2 guides.

B240059


iv.

Disconnect each connector.


v.
B238823

Detach the 6 claws and 2 guides, pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.



b.

w/ Rear No. 2 Seat:

i.
B240057

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B240055

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 3 bolts and screws.


iv.

Detach the 7 clips, 5 claws and 2 guides.


v.

Disconnect the connector and remove the deck trim side panel.

B240061



Hide 62580F 43.REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH

B240018

a.

w/o Rear No. 2 Seat:

i.

Detach the 6 clips and guide and remove the rear No. 2 window side garnish.



b.
B241940

w/ Rear No. 2 Seat:

i.

Detach the 6 clips and guide.


ii.
B240019

Detach the 7 claws and guide, pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish and remove the rear No. 2 window side garnish.



Hide 62570D 44.REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62560C 45.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH

B240020

a.

Detach the 7 clips and 4 guides.


b.
B240021

Detach the 4 claws and 2 guides, pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish and remove the rear window side garnish.


Hide 62550F 46.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74610A 47.REMOVE ASSIST GRIP SUB-ASSEMBLY

B203052E10
0.49,1.563 0.615,1.563 false 0.615,1.563 0.76,1.354 false 1.188,3.75 1.438,3.75 false 1.427,3.75 1.146,3.281 true 0.323,1.479 0.521,1.76 0.198,0.281 10 false *1 1.021,3.656 1.219,3.938 0.198,0.281 10 false *1

HINT:

Use the same procedure for the other assist grip.


a.

Using a clip remover, detach the 4 claws.

NOTICE:

Do not forcibly pry the assist grip plugs to prevent them from being deformed.


HINT:
·

Gently pry the assist grip plugs as shown in the illustration to detach the claws.

·

Tape the clip remover tip before use.



Text in Illustration
*1 Protective Tape


b.

Pull off the 2 assist grip plugs by hand.


c.
B203053

Detach the 2 clips and remove the assist grip.


d.

Remove the 2 clips from the vehicle body.


Hide 74610U 48.REMOVE REAR ASSIST GRIP ASSEMBLY

B203054E05
1.104,3.854 1.323,3.854 false 1.323,3.854 1.094,3.25 true 0.844,1.344 0.656,1.542 false 0.656,1.542 0.552,1.542 false 0.396,1.469 0.573,1.75 0.177,0.281 10 false *1 0.948,3.781 1.125,4.063 0.177,0.281 10 false *1

HINT:

Use the same procedure for the other rear assist grip.


a.

Using a clip remover, detach the 4 claws.

NOTICE:

Do not forcibly pry the assist grip plugs to prevent them from being deformed.


HINT:
·

Gently pry the rear assist grip plugs as shown in the illustration to detach the claws.

·

Tape the clip remover tip before use.



Text in Illustration
*1 Protective Tape


b.

Pull off the 2 assist grip plugs by hand.


c.
B203055

Detach the 2 clips and remove the rear assist grip.


d.

Remove the 2 clips from the vehicle body.


Hide 74631C 49.REMOVE COAT HOOK

B240022E03
1.99,1.271 2.438,1.719 false 2.448,1.719 2.563,1.719 false 2.594,1.625 2.865,1.948 0.271,0.323 10 false *1

HINT:

Use the same procedure for the other coat hook.


a.

Using a screwdriver, detach the claw and open the cover.

Text in Illustration
*1 Protective Tape


b.
B240023

Remove the screw and coat hook.


Hide 74318 50.REMOVE VISOR BRACKET COVER LH

B181706

HINT:

Use the same procedure for the other visor bracket cover.


a.

Detach the 4 claws and remove the visor bracket cover.


Hide 74317 51.REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 74320 52.REMOVE VISOR ASSEMBLY LH

B181707

a.

Remove the 2 screws and visor.


Hide 74310 53.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 54.REMOVE VISOR HOLDER

B151362E11
0.802,0.563 1.333,0.844 0.531,0.281 10 false 45°

HINT:

Use the same procedure for the other visor holder.


a.

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Detach the 2 claws and remove the visor holder.


Hide 87834 57.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 81240 58.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 63310 59.REMOVE ROOF HEADLINING ASSEMBLY

B240031

HINT:

Before removing the roof headlining, move the front seats and rear No. 1 seat to the positions shown in the illustration.


a.
B241338

w/ EC Mirror:

Disconnect the inner mirror connector.


b.
B240024

w/ Sliding Roof:

Disconnect the drive gear connector.


c.
B240025

Disconnect each connector and detach the 5 clamps from the front pillar LH.


d.
B240028

w/o Sliding Roof:

i.

Remove the 5 clips.



e.
B240029E02
0.906,2.24 0.906,2.917 true 0.625,2.24 0.906,2.917 true 1.167,2.24 0.896,2.917 true 0.885,1.021 0.885,0.344 true 1.167,1.021 0.885,0.344 true 0.615,1.021 0.885,0.344 true 1.354,1.49 1.917,1.656 true 1.354,1.75 1.917,1.667 true 1.354,1.281 1.917,1.656 true 1.344,1.99 1.906,1.667 true 0.375,2.771 0.219,2.771 false 0.219,2.771 0.469,2 true 0.365,0.479 0.208,0.479 false 0.208,0.479 0.469,1.26 true 0.354,0.375 0.604,0.563 0.25,0.188 10 false *1 0.406,2.667 0.656,2.854 0.25,0.188 10 false *1 0.844,2.927 1.094,3.115 0.25,0.188 10 false *2 1.938,1.563 2.188,1.75 0.25,0.188 10 false *2 0.802,0.156 1.052,0.344 0.25,0.188 10 false *2

w/ Sliding Roof:

i.

Remove the 5 clips.


ii.

Detach the 2 clips, 2 guides and 10 fasteners.

Text in Illustration
*1 Guide
*2 Fastener



f.
B240030

Remove the roof headlining from the back door as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when removing it.



Hide 73024 60.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B240077

a.

Detach the 4 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.


Hide 73023 61.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62440 62.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

B240066

a.

Detach the 3 clips and remove the roof side rail garnish.


Hide 62430 63.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 66425A 64.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Rear No. 2 Seat)

B240069

a.

Detach the 3 claws and remove the rear No. 2 side rail spacer.


Hide 66415A 65.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 66426B 66.REMOVE REAR NO. 3 SIDE RAIL SPACER LH (w/ Rear No. 2 Seat)

B240068

a.

Detach the 2 claws and remove the rear No. 3 side rail spacer.


Hide 66416 67.REMOVE REAR NO. 3 SIDE RAIL SPACER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 62627B 68.REMOVE QUARTER TRIM COVER

B240071

HINT:

Use the same procedure for the other quarter trim cover.


a.

Detach the 2 claws and remove the quarter trim cover.


Hide 64766 69.REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY

B240073

a.

Detach the 3 claws and 2 guides and remove the quarter trim jack cover.


Hide 64746 70.REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

B240072

a.

Detach the 2 claws and 2 guides and remove the rear combination light service cover.


Hide 64745 71.REMOVE REAR COMBINATION LIGHT SERVICE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 62597A 72.REMOVE SIDE TRIM BOX LH (w/o Rear No. 2 Seat)

B240070

a.

Remove the 2 screws.


b.

Detach the 8 claws and remove the side trim box.


Hide 62597A 73.REMOVE SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 64754B 74.REMOVE REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)

B240074

a.

Remove the 2 screws.


b.

Detach the claw and 2 guides and remove the rear floor finish side plate.


Hide 64753B 75.REMOVE REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 73372 76.REMOVE REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)

B238782

a.

Detach the claw and guide and remove the rear seat shoulder belt hanger.


Hide 73371 77.REMOVE REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.


Hide 62605Q 78.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)

B240075

a.

Detach the 4 claws and 2 guides and remove the quarter trim lid.


Hide 64746F 79.REMOVE DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)

B240076

a.

Remove the 4 screws.


b.

Detach the 2 claws and remove the deck side trim cup holder.


Hide 64745H 80.REMOVE DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure described for the LH side.