Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM1440E _59 Vehicle Exterior _056167 SLIDING ROOF / CONVERTIBLE _0274175 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 63310 2.REMOVE ROOF HEADLINING ASSEMBLY

a.

Remove the roof headlining assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 62180A 3.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

a.

Remove the curtain shield airbag assembly LH (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL).


Hide 62170A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 63218G 5.REMOVE SLIDING ROOF SIDE GARNISH LH

B234369

a.

Detach the 5 claws and remove the side garnish.


Hide 63217K 6.REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 63201G 7.REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY

B234370

a.

Using a T25 "TORX" driver, remove the 4 screws and glass.


Hide 63251H 8.REMOVE SLIDING ROOF WEATHERSTRIP

a.

Remove the sliding roof weatherstrip.


Hide 63203F 9.REMOVE SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Disconnect the 4 sliding roof drain hoses.


b.

Remove the 8 bolts and 4 nuts.

B247818


c.

Loosen the 4 nuts as shown in the illustration.

B247622

NOTICE:

Be sure that the nuts are fully threaded onto the bolts.



d.
B246952E03
1.125,0.385 1.188,0.271 1.188,0.271 1.333,0.271 false 2.552,0.385 2.615,0.26 2.615,0.26 2.74,0.26 false 1.385,0.958 1.24,0.958 false 2.813,1.125 2.688,1.125 false 0.781,0.583 0.646,0.99 0.646,0.99 0.948,0.583 true 2.438,0.76 2.031,1.083 2.031,1.083 2.188,0.771 true 1.365,0.188 1.573,0.375 0.208,0.188 10 false *1 0.583,1.01 0.802,1.188 0.219,0.177 10 false *2 1.052,0.865 1.302,1.042 0.25,0.177 10 false *3 2.76,0.198 2.969,0.385 0.208,0.188 10 false *1 1.927,1.104 2.146,1.281 0.219,0.177 10 false *2 2.563,1.063 2.813,1.24 0.25,0.177 10 false *3

Pull the sliding roof housing sub-assembly downward and detach the 2 claws of the sliding roof lock catch plate LH form the stud bolt as shown in the illustration.

Text in Illustration
*1 Bracket (Roof Panel)
*2 Sliding Roof Lock Catch Plate LH Claw
*3 Sliding Roof Housing Sub-assembly

NOTICE:

Performing this procedure breaks the claws of the sliding roof lock catch plate LH so that the sliding roof housing sub-assembly can be removed. However, do not use excessive force.



e.

Remove the 4 nuts and sliding roof housing sub-assembly.


f.
B246951

Detach the 2 claws and remove the sliding roof lock catch plate LH from the sliding roof housing sub-assembly.

HINT:

The sliding roof lock catch plate LH is used when the vehicle is assembled at the factory and is not needed for reinstallation.