Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274178 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 67001A 1.INSTALL FRONT DOOR PANEL CUSHION

a.
B240615

Attach the claw to install a new front door panel cushion.


Hide 75756C 5.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 67862 7.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B353483

Attach the 21 clips to install the front door weatherstrip LH.


Hide 68620 8.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the front door check assembly LH.


b.
A057108E60
2.156,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.198,0.156 2.417,0.354 0.219,0.198 10 false *1

Apply a few drops of adhesive to 2 or 3 threads of the bolt.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the bolt within 3 minutes of applying adhesive.



c.
B238556

Install the front door check assembly LH to the front door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Install the front door check assembly LH to the vehicle body with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 67924 9.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.

Clean the installation surface.

i.

Using a heat light, heat the installation surface.

Standard:
Item Temperature
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.



ii.

Remove the double-sided tape from the installation surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door No. 2 stiffener cushion.

i.

Using a heat light, heat a new front door No. 2 stiffener cushion and the installation surface.

Standard:
Item Temperature
Front door No. 2 stiffener cushion 20 to 30°C (68 to 86°F)
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door No. 2 stiffener cushion and vehicle body excessively.


HINT:

When installing the front door No. 2 stiffener cushion, heat the vehicle body and front door No. 2 stiffener cushion using a heat light.



ii.

Remove the peeling paper from the face of the front door No. 2 stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.
B238555E03
2.365,1.135 2.125,1.135 2.125,1.135 1.74,0.708 true 2.396,1.063 2.604,1.26 0.208,0.198 10 false *1

Attach the 2 clamps and double-sided tape to install the front door No. 2 stiffener cushion.

Text in Illustration
*1 Double-sided Tape

HINT:

Press the front door No. 2 stiffener cushion firmly to install it.



iv.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)



Hide 69312 10.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B241221E01
2.141,1.86 2.379,2.152 0.239,0.292 2.956,2.326 3.158,2.530 0.202,0.204 10 (1) 2.162,1.925 2.364,2.128 0.202,0.204 10 (2)

Install the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.


Hide 69202A 11.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly LH.


b.
B240605

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69760C 12.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B240601

Install the front door inside locking cable assembly LH to the front door lock assembly LH.


b.
B240600

Attach the 3 claws to close the cover.


Hide 69720B 13.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B240599

Install the front door lock remote control cable assembly LH to the front door lock assembly LH.


Hide 69040A 14.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 69242F 15.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.
B240596

Attach the 2 claws to install the front door rear outside handle pad LH.


Hide 69241H 16.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.
B354869

Attach the guide and 2 claws to install the front door front outside handle pad LH.


Hide 69220 17.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B240617

Insert the front end of the front door outside handle assembly LH into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly LH into the front door outside handle frame sub-assembly. Then slide the front door outside handle assembly LH toward the front of the vehicle to install it.


c.
B240616

Move the lever back in the direction indicated by the arrow in the illustration to lock the front door outside handle assembly LH.


Hide 69217E 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B240591

Using a T30 "TORX" socket wrench, install the front door outside handle cover RH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B240590

Install the hole plug.


Hide 69217F 19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B241225

Attach the claw to install the front door outside handle cover LH to the lock cylinder assembly.


Hide 20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Install the front door outside handle cover with lock cylinder assembly.

HINT:

Make sure that the lock cylinder rod is inserted into the front door lock assembly LH.



b.
B240589

Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B240588

Install the hole plug.


Hide 67404F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B242327

Install the front door rear lower frame sub-assembly LH with the bolt as shown in the illustration.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68151E 22.INSTALL FRONT DOOR GLASS RUN LH

a.
B240586

Install the front door glass run LH.


Hide 67664C 23.INSTALL DOOR FRAME GARNISH LH

a.
B240607

Attach the clip to install a new door frame garnish LH.


Hide 85720C 24.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 25.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door window regulator sub-assembly LH.


b.
B353482E06
1.781,0.26 2.021,0.26 2.021,0.26 2.115,1.208 true 1.594,0.198 1.75,0.354 0.156,0.156 10 false *1 2.656,2.01 2.875,2.25 0.219,0.24 10 true (1) 3.01,1.979 3.219,2.135 0.208,0.156 10 true (3) 2.208,2.375 2.417,2.615 0.208,0.24 10 true (6) 1.635,2.479 1.844,2.688 0.208,0.208 10 true (5) 1.781,1.104 1.99,1.302 0.208,0.198 10 true (4) 3.125,1.573 3.323,1.813 0.198,0.24 10 true (2)

Install the temporary bolt to the front door window regulator sub-assembly LH.

Text in Illustration
*1 Temporary Bolt


c.

Temporarily install the front door window regulator sub-assembly LH.


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator sub-assembly LH.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68102 26.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the multiplex network master switch assembly (for Driver Side).


b.

Connect the power window regulator switch assembly (for Front Passenger Side).


c.

Connect the cable to the negative (-) battery terminal.


d.

Move the front door glass sub-assembly so that the front door glass bolts can be seen.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



f.

Disconnect the multiplex network master switch assembly (for Driver Side).


g.

Disconnect the power window regulator switch assembly (for Front Passenger Side).


h.
B353492E01
2.048,0.026 2.247,0.208 0.199,0.182 10 (1) 0.814,0 1.012,0.182 0.199,0.182 10 (2)

Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.


i.
B353480E02
1.646,1.969 1.844,2.135 0.198,0.167 10 true (1) 2.5,1.927 2.698,2.094 0.198,0.167 10 true (2)

Install the front door glass sub-assembly LH with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 87940 27.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67832 28.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply a new butyl tape to the front door panel.


b.
B240610E02
0.208,0.208 0.417,0.427 0.208,0.219 10 false *1 3.083,0.219 3.292,0.438 0.208,0.219 10 false *1

Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.


c.

Install a new front door service hole cover LH according to the reference points on the front door panel.

Text in Illustration
*1 Reference Point

NOTICE:

Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



d.
B240582

Attach the 2 clamps.


e.

Connect the door wire with the bolt.


Hide 84927 31.INSTALL SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 84810 32.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84930 33.INSTALL DOOR CONTROL SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84040 34.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 81080J 36.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

a.
E199225

Connect the connector.


b.

Attach the claw to install the light.


Hide 68172A 37.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B240611

Attach the 4 claws to install the front door inner glass weatherstrip LH as shown in the illustration.


Hide 67602 38.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B240612

Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


b.
B240574

Connect the connector.


c.
B354466E02
2.208,4.104 2.292,4.104 2.292,4.104 2.438,3.833 false 1.396,4.125 1.313,4.125 1.313,4.125 1.167,3.854 false 2.021,4.031 2.177,4.208 0.156,0.177 10 false *1 1.448,4.031 1.604,4.208 0.156,0.177 10 false *1

Attach the front door trim board sub-assembly LH to the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.


d.

Attach the reference boss.

Text in Illustration
*1 Reference Boss


e.
B353478

Attach the 11 clips to install the front door trim board sub-assembly LH.


f.

Install the 3 screws.


g.
B353477

Attach the 4 claws to install the 2 door armrest caps.


Hide 69298A 39.INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B357473

Attach the 3 claws to install the No. 2 door inside handle bezel LH.


Hide 67492A 40.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B240255

Attach the 2 clips to install the front door lower frame bracket garnish LH.


Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 42.INITIALIZE POWER WINDOW CONTROL SYSTEM