Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056169 MIRROR (EXT) _0274186 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Side Turn Signal Light)

B239061E02
2.01,3.427 2.188,2.458 2.188,2.458 2.448,2.458 false 2.208,3.406 2.396,2.75 2.396,2.75 2.552,2.75 false 2.396,3.406 2.635,3.094 2.635,3.094 2.771,3.094 false 1.552,2.385 1.802,2.563 0.25,0.177 10 false *a 2.823,3.021 3.052,3.167 0.229,0.146 10 false MV 1.469,1.729 1.74,2.01 0.271,0.281 10 true (B) 0.854,1.24 1.094,1.552 0.24,0.313 10 true (C) 1.458,0.521 1.729,0.823 0.271,0.302 10 true (A) 2.042,1.073 2.281,1.375 0.24,0.302 10 true (D) 2.625,2.667 2.854,2.813 0.229,0.146 10 false M+ 2.5,2.396 2.771,2.542 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left (C)
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B239055E03
1.385,3.417 1.115,2.677 1.115,2.677 0.885,2.677 false 1.385,3.771 1.115,4.323 1.115,4.323 0.875,4.323 false 1.688,2.25 1.854,2.51 0.167,0.26 10 false *a 0.677,2.594 0.927,2.802 0.25,0.208 10 false H+ 0.698,4.229 0.938,4.438 0.24,0.208 10 false H-

Check the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (HL+) - Terminal 8 (HL-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (HL+)
Battery negative (-) → Terminal 8 (HL-)
Mirror becomes warm


HINT:

It will take a short amount of time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



c.
B242793E01
1.631,2.262 1.954,2.494 0.323,0.232 10 *a

Apply battery voltage to the connector and check the LED illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 11
LED illuminates


If the result is not as specified, check the side turn signal light assembly LH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Side Turn Signal Light)

B239062E02
1.563,3.469 1.406,3.094 1.406,3.094 1.167,3.094 false 1.802,3.365 1.99,2.708 1.99,2.708 2.156,2.708 false 2.042,3.396 2.333,3.083 2.333,3.083 2.5,3.083 false 1.563,2.406 1.813,2.583 0.25,0.177 10 false *a 0.917,3.021 1.146,3.167 0.229,0.146 10 false MV 1.479,1.719 1.729,2.042 0.25,0.323 10 true (B) 0.854,1.25 1.094,1.625 0.24,0.375 10 true (C) 1.438,0.542 1.698,0.813 0.26,0.271 10 true (A) 2.042,1.083 2.292,1.365 0.25,0.281 10 true (D) 2.208,2.635 2.438,2.781 0.229,0.146 10 false M+ 2.542,3.01 2.813,3.156 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward (A)
Battery negative (-) → Terminal 3 (MV)
Battery positive (+) → Terminal 1 (M+)
Turns downward (B)
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns left (C)
Battery negative (-) → Terminal 2 (MH)
Battery positive (+) → Terminal 1 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B239056E03
1.594,3.74 1.396,4.188 1.396,4.188 1.229,4.188 false 1.833,3.74 2.031,4.188 2.031,4.188 2.198,4.188 false 1.625,2.302 1.792,2.563 0.167,0.26 10 false *a 0.885,4.104 1.281,4.313 0.396,0.208 10 false HL+ 2.281,4.104 2.521,4.313 0.24,0.208 10 false HL-

Check the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (HL+) - Terminal 5 (HL-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (HL+)
Battery negative (-) → Terminal 5 (HL-)
Mirror becomes warm


HINT:

It will take a short amount of time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Side Turn Signal Light)

B239057E02
2.031,3.417 2.208,2.448 2.208,2.448 2.469,2.448 false 2.219,3.406 2.406,2.75 2.406,2.75 2.563,2.75 false 2.406,3.417 2.646,3.104 2.646,3.104 2.781,3.104 false 1.563,2.396 1.813,2.573 0.25,0.177 10 false *a 2.823,3.031 3.052,3.177 0.229,0.146 10 false MV 1.969,1.719 2.229,2.063 0.26,0.344 10 true (B) 2.531,1.24 2.813,1.552 0.281,0.313 10 true (C) 1.969,0.531 2.208,0.823 0.24,0.292 10 true (A) 1.365,1.063 1.573,1.333 0.208,0.271 10 true (D) 2.615,2.677 2.844,2.823 0.229,0.146 10 false M+ 2.51,2.375 2.781,2.521 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left (C)
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B239059E04
1.385,3.417 1.104,2.677 1.104,2.677 0.875,2.677 false 1.385,3.771 1.115,4.323 1.115,4.323 0.885,4.323 false 1.677,2.25 1.844,2.51 0.167,0.26 10 false *a 0.646,2.594 0.896,2.802 0.25,0.208 10 false H+ 0.688,4.229 0.927,4.438 0.24,0.208 10 false H-

Check the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (HR+) - Terminal 8 (HR-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (HR+)
Battery negative (-) → Terminal 8 (HR-)
Mirror becomes warm


HINT:

It will take a short amount of time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)



c.
B242794E01
1.668,2.432 1.862,2.636 0.194,0.205 10 *a

Apply battery voltage to the connector and check the LED illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 11
LED illuminates


If the result is not as specified, check the side turn signal light assembly RH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Side Turn Signal Light)

B239058E02
1.635,3.354 1.469,2.979 1.469,2.979 1.229,2.979 false 1.875,3.26 2.063,2.604 2.063,2.604 2.229,2.604 false 2.094,3.281 2.385,2.969 2.385,2.969 2.552,2.969 false 1.979,1.729 2.208,2.083 0.229,0.354 10 true (B) 2.531,1.24 2.781,1.531 0.25,0.292 10 true (C) 1.969,0.49 2.219,0.813 0.25,0.323 10 true (A) 1.354,1.042 1.583,1.365 0.229,0.323 10 true (D) 1.635,2.292 1.885,2.469 0.25,0.177 10 false *a 0.979,2.906 1.208,3.052 0.229,0.146 10 false MV 2.271,2.531 2.5,2.677 0.229,0.146 10 false M+ 2.594,2.896 2.865,3.042 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward (A)
Battery negative (-) → Terminal 3 (MV)
Battery positive (+) → Terminal 1 (M+)
Turns downward (B)
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns left (C)
Battery negative (-) → Terminal 2 (MH)
Battery positive (+) → Terminal 1 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B239060E03
1.49,3.74 1.292,4.188 1.292,4.188 1.125,4.188 false 1.74,3.75 1.938,4.198 1.938,4.198 2.104,4.198 false 1.521,2.302 1.688,2.563 0.167,0.26 10 false *a 0.917,4.115 1.167,4.323 0.25,0.208 10 false H+ 2.156,4.115 2.396,4.323 0.24,0.208 10 false H-

Check the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (HR+) - Terminal 5 (HR-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (HR+)
Battery negative (-) → Terminal 5 (HR-)
Mirror becomes warm


HINT:

It will take a short amount of time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)