Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › from 2013.08
RM1440E _59 Vehicle Exterior _056169 MIRROR (EXT) _0274186 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Side Turn Signal Light)

a.
B353495E03
2.854,2.604 2.302,2.604 true 2.854,1.896 2.406,1.896 2.406,1.896 2.125,2.542 true 1.875,2.542 1.729,1.823 1.729,1.823 1.531,1.823 true 0.271,1.604 0.479,1.781 0.208,0.177 10 false *a 2.938,2.531 3.198,2.708 0.26,0.177 10 false MV 2.927,1.823 3.167,2 0.24,0.177 10 false M+ 1.271,1.75 1.563,1.927 0.292,0.177 10 false MH

Apply battery voltage and check the operation of the outer mirror LH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.


b.
B353496E02
0.625,3.198 0.979,3.198 0.979,3.198 1.271,2.875 true 0.667,1.885 0.927,1.885 0.927,1.885 1.26,2.563 true 1.594,1.771 1.823,2 0.229,0.229 10 false *a 0.365,3.104 0.698,3.333 0.333,0.229 10 false HL- 0.385,1.802 0.719,2.031 0.333,0.229 10 false HL+

Check the outer mirror heater LH.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (HL+) - Terminal 8 (HL-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage to check the operation of the outer mirror heater LH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2 (HL+)
Battery negative (-) → Terminal 8 (HL-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

HINT:

It will take a short amount of time for the outer mirror LH to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the side turn signal light assembly LH.

i.
B353497E01
0.562,1.48 0.857,1.735 0.295,0.254 10 *a

Apply battery voltage to the connector to check the illumination condition.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 11
Side turn signal light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, inspect the side turn signal light assembly LH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Side Turn Signal Light)

a.
B353498E03
1.458,2.615 0.969,2.615 true 2.49,1.802 1.698,1.802 1.698,1.802 1.698,2.438 true 1.938,2.521 2.542,2.521 true 0.177,1.656 0.406,1.844 0.229,0.188 10 false *a 0.708,2.531 0.938,2.719 0.229,0.188 10 false MV 2.583,1.729 2.813,1.917 0.229,0.188 10 false M+ 2.604,2.448 2.854,2.635 0.25,0.188 10 false MH

Apply battery voltage to check the operation of the outer mirror LH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward
Battery negative (-) → Terminal 3 (MV)
Battery positive (+) → Terminal 1 (M+)
Turns downward
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns left
Battery negative (-) → Terminal 2 (MH)
Battery positive (+) → Terminal 1 (M+)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

If the result is not as specified, replace the outer rear view mirror assembly LH.


b.

Check the outer mirror heater LH.

i.
B354441E02
1.531,2.875 0.958,2.875 true 1.854,2.865 2.417,2.865 true 0.25,1.573 0.427,1.76 0.177,0.188 10 false *a 0.635,2.781 0.927,2.969 0.292,0.188 10 false HL+ 2.49,2.781 2.781,2.969 0.292,0.188 10 false HL-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (HL+) - Terminal 5 (HL-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage to check the operation of the outer mirror heater LH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 4 (HL+)
Battery negative (-) → Terminal 5 (HL-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)

HINT:

It will take a short amount of time for the outer mirror LH to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Side Turn Signal Light)

a.
B354442E03
2.302,2.615 2.74,2.615 true 2.083,2.531 2.229,2.167 2.229,2.167 2.729,2.167 true 1.917,2.531 1.917,1.719 1.917,1.719 2.115,1.719 true 0.25,1.646 0.458,1.823 0.208,0.177 10 false *a 2.813,2.542 3.104,2.719 0.292,0.177 10 false MV 2.823,2.083 3.115,2.26 0.292,0.177 10 false M+ 2.177,1.635 2.427,1.813 0.25,0.177 10 false MH

Apply battery voltage to check the operation of the outer mirror RH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.


b.

Check the outer mirror heater RH.

i.
B354443E03
0.708,2.229 0.927,2.229 0.927,2.229 1.26,2.552 true 0.646,3.125 0.938,3.125 0.938,3.125 1.271,2.885 true 1.604,1.708 1.833,1.885 0.229,0.177 10 false *a 0.385,2.146 0.708,2.323 0.323,0.177 10 false HR+ 0.365,3.031 0.677,3.208 0.313,0.177 10 false HR-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (HR+) - Terminal 8 (HR-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage to check the operation of the outer mirror heater RH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2 (HR+)
Battery negative (-) → Terminal 8 (HR-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

HINT:

It will take a short amount of time for the outer mirror RH to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the side turn signal light assembly RH.

i.
B354444E01
0.64,1.521 0.908,1.762 0.268,0.241 10 *a

Apply battery voltage to the connector to check the illumination condition.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 10
Battery negative (-) → Terminal 11
Side turn signal light illuminates


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, inspect the side turn signal light assembly RH (See page Vehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION).

If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Side Turn Signal Light)

a.
B354445E03
1.448,2.563 1.135,2.198 1.135,2.198 0.865,2.198 true 1.74,2.49 2.031,1.917 2.031,1.917 2.271,1.917 true 1.938,2.542 2.51,2.542 true 1.615,1.594 1.802,1.781 0.188,0.188 10 false *a 0.604,2.115 0.917,2.302 0.313,0.188 10 false MV 2.333,1.844 2.594,2.031 0.26,0.188 10 false M+ 2.604,2.469 2.865,2.656 0.26,0.188 10 false MH

Apply battery voltage to check the operation of the outer mirror.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 3 (MV)
Battery negative (-) → Terminal 1 (M+)
Turns upward
Battery negative (-) → Terminal 3 (MV)
Battery positive (+) → Terminal 1 (M+)
Turns downward
Battery positive (+) → Terminal 2 (MH)
Battery negative (-) → Terminal 1 (M+)
Turns left
Battery negative (-) → Terminal 2 (MH)
Battery positive (+) → Terminal 1 (M+)
Turns right


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

If the result is not as specified, replace the outer rear view mirror assembly RH.


b.

Check the outer mirror heater RH.

i.
B354446E02
0.948,2.896 1.552,2.896 true 2.542,2.885 1.854,2.885 true 0.583,1.656 0.76,1.813 0.177,0.156 10 false *a 0.604,2.813 0.927,2.969 0.323,0.156 10 false HR+ 2.615,2.802 2.938,2.958 0.323,0.156 10 false HR-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (HR+) - Terminal 5 (HR-) 25°C (77°F) 5.3 to 7.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage to check the operation of the outer mirror heater RH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 4 (HR+)
Battery negative (-) → Terminal 5 (HR-)
Mirror becomes warm


Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)

HINT:

It will take a short amount of time for the outer mirror RH to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.