Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274189 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149717E02
1.625,1.469 1.865,1.219 1.865,1.219 1.948,1.219 false 1.625,1.823 1.865,1.583 1.865,1.583 1.948,1.583 false 1.625,2.135 1.865,1.896 1.865,1.896 1.948,1.896 false 0.896,1.573 1.104,1.729 0.208,0.156 10 false 2F 1.083,3.875 1.365,4.031 0.281,0.156 10 false F10 0.896,2.167 1.104,2.323 0.208,0.156 10 false 2D 5.865,1.49 6.073,1.646 0.208,0.156 10 false 2B 5.865,2.188 6.073,2.344 0.208,0.156 10 false 2C 1.073,2.76 1.281,2.917 0.208,0.156 10 false 2E 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.958,1.156 2.229,1.302 0.271,0.146 10 false F8 1.958,1.51 2.229,1.656 0.271,0.146 10 false F9 1.958,1.833 2.229,1.979 0.271,0.146 10 false F10 3.625,3.865 3.823,4.021 0.198,0.156 10 false F9 1.125,5.177 1.344,5.333 0.219,0.156 10 false 2F 1.885,6.406 2.104,6.563 0.219,0.156 10 false 2B 4.938,6.396 5.156,6.552 0.219,0.156 10 false 2C 3.51,7.677 3.646,7.833 0.135,0.156 10 false A 3.948,5.177 4.146,5.333 0.198,0.156 10 false 2D 5.896,5.177 6.094,5.333 0.198,0.156 10 false 2E 5.948,3.865 6.146,4.021 0.198,0.156 10 false F8

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU).


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F10-8 (RWSW) - Body ground P - Body ground Rear washer switch input Ignition switch ON, rear washer switch on Below 1 V
F10-8 (RWSW) - Body ground P - Body ground Rear washer switch input Ignition switch ON, rear washer switch off Pulse generation (See waveform 1 or 2)
F10-17 (RWLS) - Body ground R- Body ground Rear wiper switch input Ignition switch ON, rear wiper switch INT Below 1 V
F10-17 (RWLS) - Body ground R - Body ground Rear wiper switch input Ignition switch ON, rear wiper switch off Pulse generation (See waveform 1 or 2)
F9-1 (RWC1) - Body ground B - Body ground Rear wiper switch input Ignition switch ON, rear wiper switch LO Below 1 V
F9-1 (RWC1) - Body ground B- Body ground Rear wiper switch input Ignition switch ON, rear wiper switch off Pulse generation (See waveform 1 or 2)
F8-2 (BW) - Body ground B - Body ground Rear washer washer relay operation output Ignition switch ON, rear wiper switch on Below 1 V
F8-2 (BW) - Body ground B - Body ground Rear washer washer relay operation output Ignition switch ON, rear wiper switch off 11 to 14 V

If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol)

F10-8 (RWSW) - Body ground

F10-17 (RWLS) - Body ground

F9-1 (RWC1) - Body ground


Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch ON, rear washer switch off


f.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol)

F10-8 (RWSW) - Body ground

F10-17 (RWLS) - Body ground

F9-1 (RWC1) - Body ground


Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch ON, rear washer switch off



CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


U149778E02
2.833,0.406 3.083,0.594 0.25,0.188 10 false V2

a.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V2-7 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the V2 multiplex network door ECU (back door P/W) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-3 (W) - V2-12 (SGND) R - G Rear wiper reverse position switch input Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off) Pulse generation (See waveform 1)
V2-3 (W) - V2-12 (SGND) R - G Rear wiper reverse position switch input Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on) Pulse generation (See waveform 2)
V2-4 (P) - V2-12 (SGND) V - G Rear wiper retractable position switch input Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off) Pulse generation (See waveform 3)
V2-4 (P) - V2-12 (SGND) V - G Rear wiper retractable position switch input Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on) Pulse generation (See waveform 4)
V2-2 (WIP+) - V2-6 (GND) L - W-B Rear wiper motor output Ignition switch ON, rear wiper switch INT Pulse generation (See waveform 5)
V2-5 (WIP-) - V2-6 (GND) P - W-B Rear wiper motor output Ignition switch ON, rear wiper switch INT Pulse generation (See waveform 6)
V2-2 (WIP+) - V2-6 (GND) L - W-B Rear wiper motor output Ignition switch ON, rear wiper switch LO Pulse generation (See waveform 7)
V2-5 (WIP-) - V2-6 (GND) P - W-B Rear wiper motor output Ignition switch ON, rear wiper switch LO Pulse generation (See waveform 8)
V2-2 (WIP+) - V2-6 (GND) L - W-B Rear wiper motor output Ignition switch ON, rear washer switch on Pulse generation (See waveform 9)
V2-5 (WIP-) - V2-6 (GND) P - W-B Rear wiper motor output Ignition switch ON, rear washer switch on Pulse generation (See waveform 10)
V2-2 (WIP+) - V2-6 (GND) L - W-B Rear wiper motor output Ignition switch ON, rear wiper switch off Pulse generation (See waveform 11)
V2-5 (WIP-) - V2-6 (GND) P - W-B Rear wiper motor output Ignition switch ON, rear wiper switch off Pulse generation (See waveform 12)

If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.


e.
B242627E01
0.095,0.96 0.436,1.129 0.341,0.170 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) V2-3 (W) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off)


f.
B242628E01
0.118,0.96 0.454,1.115 0.336,0.156 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) V2-3 (W) - V2-12 (SGND)
Tool Setting 5 V/DIV., 10 ms/DIV
Condition Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on)


g.
B242627E01
0.095,0.96 0.436,1.129 0.341,0.170 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) V2-4 (P) - V2-12 (SGND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off)


h.
B242628E01
0.118,0.96 0.454,1.115 0.336,0.156 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) V2-4 (P) - V2-12 (SGND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on)


i.
B242631E01
0.29,1.797 0.631,1.949 0.341,0.151 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) V2-2 (WIP+) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch INT


j.
B242632E01
0.307,1.783 0.634,1.939 0.327,0.156 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) V2-5 (WIP-) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch INT


k.
B242635E01
0.262,1.815 0.609,1.960 0.347,0.145 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) V2-2 (WIP+) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch LO


l.
B242636E01
0.29,1.796 0.640,1.952 0.350,0.156 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) V2-5 (WIP-) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch LO


m.
B242639E01
0.29,1.78 0.636,1.945 0.346,0.165 10 GND

Using an oscilloscope, check waveform 9.

Waveform 9 (Reference)
Item Content
Terminal No. (Symbol) V2-2 (WIP+) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear washer switch on


n.
B242640E02
0.333,1.802 0.792,2 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 10.

Waveform 10 (Reference)
Item Content
Terminal No. (Symbol) V2-5 (WIP-) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear washer switch on


o.
B242643E01
0.118,0.998 0.454,1.145 0.336,0.147 10 GND

Using an oscilloscope, check waveform 11.

Waveform 11 (Reference)
Item Content
Terminal No. (Symbol) V2-2 (WIP+) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch off


p.
B242644E01
0.266,1.785 0.596,1.947 0.330,0.163 10 GND

Using an oscilloscope, check waveform 12.

Waveform 12 (Reference)
Item Content
Terminal No. (Symbol) V2-5 (WIP-) - V2-6 (GND)
Tool Setting 2 V/DIV., 2 ms/DIV
Condition Ignition switch ON, rear wiper switch off