Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274191 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85120R 1.INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY

a.
E198998

Attach the 2 guides and temporally install the rear wiper motor and bracket assembly with the 3 bolts.


b.

Tighten the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 2.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
E199088E03
0.917,1.417 1.188,1.677 1.188,1.677 1.469,1.677 true 1.542,1.583 1.719,1.781 0.177,0.198 10 false *1

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Pivot Serrations


b.
E199087E01
0.363,0.592 0.622,0.817 0.260,0.224 10 *2 2.782,0.868 3.042,1.093 0.260,0.224 10 *1 0.581,0.696 0.974,0.696 0.974,0.696 1.219,0.942 false 2.742,0.947 2.578,0.947 2.578,0.947 2.18,1.231 false

Clean the wiper pivot serrations with a wire brush.

Text in Illustration
*1 Wiper Pivot Serrations
*2 Wire Brush


c.

Operate the rear wiper and stop the rear wiper motor at the automatic stop position.

HINT:

The wiper motor does not operate if the back door and back door glass are not closed.



d.
E199089E02
1.104,1.833 1.219,1.833 1.219,1.833 1.292,2.302 false 1.625,1.979 1.573,1.979 1.573,1.979 1.5,2.354 true 2.094,2.802 1.635,2.802 true 0.083,0.073 0.333,0.271 0.25,0.198 10 false *A 0.958,1.74 1.156,1.938 0.198,0.198 10 false *1 1.656,1.906 1.833,2.104 0.177,0.198 10 false *2 2.135,2.719 2.313,2.917 0.177,0.198 10 false *3

With the rear wiper blade and linear wiper step in the positions shown in the illustration, install the rear wiper blade assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

Text in Illustration
*A Tightening Position
*1 Linear Wiper Step
*2 Wiper Blade Rubber Block
*3 Wiper Blade

HINT:

Hold the arm hinge down by hand while tightening the nut.



e.
E199090E03
1.198,1.792 1.083,1.792 1.083,1.792 1.052,1.865 false 1.656,2.031 1.594,2.031 1.594,2.031 1.51,2.406 false 1.99,2.958 1.708,2.958 1.708,2.958 1.646,2.917 true 0.042,0 0.271,0.24 0.229,0.24 10 false *A 1.229,1.708 1.458,1.958 0.229,0.25 10 false *1 1.656,1.917 1.885,2.156 0.229,0.24 10 false *2 2.021,2.865 2.25,3.104 0.229,0.24 10 false *3

Place the rear wiper blade assembly in the automatic stop position.

Text in Illustration
*A Rise-up Position
*1 Linear Wiper Step
*2 Wiper Blade Rubber Block
*3 Wiper Blade


Hide 76085 3.INSTALL REAR SPOILER SUB-ASSEMBLY

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).