Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM1440E _59 Vehicle Exterior _056173 EXTERIOR PANELS / TRIM _0274232 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing the clip, heat the vehicle body and clip using a heat light.

Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Clip 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the vehicle body or clip excessively.


PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:
·

If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.

·

If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.



a.
B187426E03
2.064,0.824 2.371,0.824 false 1.851,0.727 2.080,0.914 0.229,0.187 10 *1 0.767,0.944 0.971,1.141 0.205,0.198 10 *a 0.986,1.073 1.226,1.073 1.226,1.073 1.347,1.528 false

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

Text in Illustration
*1 Adhesive
*a 2 to 3 mm (0.0787 to 0.118 in.) Bead of Adhesive

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2) or more (when the temperature is 23°C (73°F))



b.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.

While using the position shown in the illustration as a reference, place the No. 1 roof drip side finish moulding clip onto the roof panel. Then position and install the clip after lightly pressing it so that the adhesive adheres to the primer.

B239347E01
1.188,0.079 1.365,0.262 0.177,0.184 10 *a 4.621,0.079 4.798,0.262 0.177,0.184 10 *b 1.821,1.312 1.932,1.488 0.111,0.177 10 a 2.244,1.22 2.369,1.388 0.125,0.169 10 b 1.462,0.504 1.579,0.671 0.118,0.166 10 c 5.185,1.323 5.309,1.487 0.124,0.164 10 d 5.496,1.309 5.621,1.468 0.125,0.159 10 e 5.542,0.338 5.646,0.508 0.104,0.170 10 f

Text in Illustration
*a for Front Side *b for Rear Side

Reference Value:
Area Specified Condition Area Measurement
a 5.1 to 5.6 mm
(0.201 to 0.220 in.)
b 5.8 mm
(0.228 in.)
c 6.05 to 6.1 mm
(0.238 to 0.240 in.)
d 5 mm
(0.197 in.)
e 5 to 5.5 mm
(0.197 to 0.217 in.)
f 10.5 to 11 mm
(0.413 to 0.433 in.)


Install the rear roof drip side finish moulding when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clip.

HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75552 2.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

a.

Attach the clip to install the roof drip side finish moulding.


Hide 75556C 3.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING LH

a.

Install the center roof drip side finish moulding.


Hide 75554 4.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

a.

Attach the clip to install the roof drip side finish moulding.


Hide 63185H 5.INSTALL ROOF RACK BRACKET (w/o Roof Rack)

HINT:

Use the same procedure to install the roof rack bracket on the other side.


a.

Install the roof rack bracket with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 75596D 6.INSTALL FRONT ROOF DRIP SIDE MOULDING COVER LH (w/o Roof Rack)

HINT:

Use the same procedure to install the roof drop side finish moulding cover on the other side.


a.

Attach the 2 clips to install the front roof drip side moulding cover.


Hide 7.INSTALL ROOF RAIL ASSEMBLY LH (w/ Roof Rack)

a.

Install the roof rail assembly LH (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>ROOF RACK>INSTALLATION).