Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.12
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM

A227113E08
1.813,1.469 2.219,1.75 0.406,0.281 10 false ST1 1.813,2.219 2.208,2.49 0.396,0.271 10 false ST2 1.333,1.469 1.719,1.75 0.385,0.281 10 false AM1 0.25,2.365 0.667,2.635 0.417,0.271 10 false AM1 1.344,2.219 1.698,2.49 0.354,0.271 10 false AM2 2.167,1.208 2.396,1.49 0.229,0.281 10 false 1 2.167,1.958 2.406,2.26 0.24,0.302 10 false 8 1.156,1.208 1.385,1.479 0.229,0.271 10 false 2 1.167,1.958 1.385,2.208 0.219,0.25 10 false 7 1.26,2.5 1.625,2.76 0.365,0.26 10 false F15 1.25,2.667 2.354,3 1.104,0.333 10 false Ignition Switch 5.844,1.146 6.135,1.5 0.292,0.354 10 false 2 5.125,1.76 5.406,2.031 0.281,0.271 10 false 4 4.896,2.604 5.167,2.906 0.271,0.302 10 false 5 5.76,1.344 6.188,1.667 0.427,0.323 10 false B37 6.094,1.333 6.583,1.594 0.49,0.26 10 false NSW 5.063,2.594 5.479,2.813 0.417,0.219 10 false B51 5.063,2.781 5.844,3.594 0.781,0.813 10 false Park/Neutral Position Switch Assembly 0.927,3.208 1.24,3.479 0.313,0.271 10 false ST 3.688,4.49 4.115,4.844 0.427,0.354 10 false ST 1.156,4.25 1.438,4.521 0.281,0.271 10 false 1 1.969,4.135 2.219,4.417 0.25,0.281 10 false 1 1.125,4.458 1.5,4.76 0.375,0.302 10 false C3 2.198,4.177 2.542,4.5 0.344,0.323 10 false C6 1.052,5.823 1.708,6.198 0.656,0.375 10 false Battery 1.573,5.271 2.875,5.708 1.302,0.438 10 false Starter Assembly 3.323,3.635 3.604,3.896 0.281,0.26 10 false 3 4.125,3.635 4.396,3.927 0.271,0.292 10 false 5 3.333,4.063 3.604,4.333 0.271,0.271 10 false 2 4.125,4.063 4.354,4.323 0.229,0.26 10 false 1 5.802,3.979 6.063,4.229 0.26,0.25 10 false 10 5.76,4.177 6.198,4.5 0.438,0.323 10 false F50 6.094,4.177 6.51,4.469 0.417,0.292 10 false STA 6.292,4.635 6.792,5.01 0.5,0.375 10 false ECM 0.271,3.823 0.656,4.052 0.385,0.229 10 false ALT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read the value.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK STARTER RELAY (ST) (POWER SOURCE)
2.CHECK STARTER RELAY (ST) (POWER SOURCE)
a.
A227799E01
1.405,0.527 1.566,0.688 0.161,0.161 10 *1 1.629,3.077 1.789,3.237 0.161,0.161 10 *2

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Text in Illustration
*1 Starter Relay (ST)
*2 Engine Room Relay Block


c.

Reinstall the starter relay (ST).



OK

3.INSPECT STARTER RELAY (ST)

NG

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.INSPECT STARTER RELAY (ST)
a.

Inspect the starter relay (ST) (See page Engine / Hybrid System>1GR-FE STARTING>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)

NG

REPLACE STARTER RELAY (ST)

4.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 2 - Body ground Always Below 1 Ω



c.

Reinstall the starter relay (ST).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BODY GROUND)

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the starter relay (ST) from the engine room relay block.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 - B51-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Starter relay (ST) terminal 1 or B51-5 - Body ground Always 10 kΩ or higher



d.

Reinstall the starter relay (ST).


e.

Reconnect the park/neutral position switch assembly connector.



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B51-4 - F15-1 (ST1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B51-4 or F15-1 (ST1) - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch assembly connector.


e.

Reconnect the ignition switch assembly connector.



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1GR-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY