Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2016.12
RM1440E _59 Vehicle Exterior _056167 SLIDING ROOF / CONVERTIBLE _0274174 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2342 The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof switch)

·

Harness or connector



WIRING DIAGRAM

B467741E01
4.063,4.229 6.604,4.635 2.542,0.406 10 false Sliding Roof Drive Gear Sub-assembly 4.073,4.031 4.542,4.344 0.469,0.313 10 false S10 4.458,2.135 5.229,2.646 0.771,0.51 10 false Sliding Roof ECU 5.448,1.125 6.792,1.521 1.344,0.396 10 false Sliding Roof Motor 5.708,2.792 6.344,3.146 0.635,0.354 10 false Hall IC 5.698,2.052 6.333,2.406 0.635,0.354 10 false Hall IC 0.313,3.438 3.063,3.844 2.75,0.406 10 false Map Light Assembly (Sliding Roof Switch) 0.323,3.25 0.792,3.563 0.469,0.313 10 false U2 0.844,1.792 1.385,2.063 0.542,0.271 10 false GND 2.063,1.635 2.604,1.906 0.542,0.271 10 false OPN 2.094,1.99 2.635,2.26 0.542,0.271 10 false CLS 2.167,2.375 2.708,2.646 0.542,0.271 10 false UP 1.917,2.75 2.458,3.021 0.542,0.271 10 false DOWN 3.844,1.063 4.385,1.333 0.542,0.271 10 false E 3.813,1.635 4.354,1.906 0.542,0.271 10 false OPN 3.813,1.99 4.354,2.26 0.542,0.271 10 false CLS 3.823,2.385 4.365,2.656 0.542,0.271 10 false UP 3.813,2.76 4.354,3.031 0.542,0.271 10 false DWN 0.646,1.792 1,2.052 0.354,0.26 10 false 1 2.5,1.635 2.854,1.896 0.354,0.26 10 false 3 2.5,1.979 2.854,2.24 0.354,0.26 10 false 2 2.51,2.375 2.865,2.635 0.354,0.26 10 false 5 2.521,2.76 2.875,3.021 0.354,0.26 10 false 4 3.542,1.052 3.896,1.313 0.354,0.26 10 false 12 3.594,1.625 3.948,1.885 0.354,0.26 10 false 7 3.583,1.99 3.938,2.25 0.354,0.26 10 false 5 3.583,2.375 3.938,2.635 0.354,0.26 10 false 4 3.573,2.75 3.927,3.01 0.354,0.26 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2342 is output A
DTC is not output B



A

2.READ VALUE USING GTS (SLIDING ROOF)

B

2.READ VALUE USING GTS (SLIDING ROOF)
a.

Using the GTS, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Failure (Past) Slide open switch failure signal (Past) / ON or OFF ON: Slide open switch signal failure (Past)
OFF: No slide open switch signal failure (Past)
-
Close Switch Failure (Past) Slide close switch failure signal (Past) / ON or OFF ON: Slide close switch signal failure (Past)
OFF: No slide close switch signal failure (Past)
-
Up Switch Failure (Past) Tilt up switch failure signal (Past) / ON or OFF ON: Tilt up switch signal failure (Past)
OFF: No tilt up switch signal failure (Past)
-
Down Switch Failure (Past) Tilt down switch failure signal (Past) / ON or OFF ON: Tilt down switch signal failure (Past)
OFF: No tilt down switch signal failure (Past)
-
Open Switch Failure (Current) Slide open switch failure signal (Current) / ON or OFF ON: Slide open switch signal failure (Current)
OFF: No slide open switch signal failure (Current)
-
Close Switch Failure (Current) Slide close switch failure signal (Current) / ON or OFF ON: Slide close switch signal failure (Current)
OFF: No slide close switch signal failure (Current)
-
Up Switch Failure (Current) Tilt up switch failure signal (Current) / ON or OFF ON: Tilt up switch signal failure (Current)
OFF: No tilt up switch signal failure (Current)
-
Down Switch Failure (Current) Tilt down switch failure signal (Current) / ON or OFF ON: Tilt down switch signal failure (Current)
OFF: No tilt down switch signal failure (Current)
-

OK:

"OFF" appears on the GTS screen.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
E198779C05
2.427,0.75 2.302,0.75 2.302,0.75 2.208,1.156 true 2.313,0.49 2.188,0.49 2.188,0.49 2.094,1.167 true 2.198,0.229 2.073,0.229 2.073,0.229 1.979,1.167 true 1.552,0.24 1.708,0.24 1.708,0.24 1.865,1.156 true 1.406,0.521 1.563,0.521 1.563,0.521 1.75,1.146 true 0.156,0.115 0.552,0.469 0.396,0.354 10 false *a 2.5,0.677 3.042,1.052 0.542,0.375 10 false GND 2.26,0.156 2.76,0.417 0.5,0.26 10 false OPN 2.375,0.406 2.958,0.792 0.583,0.385 10 false CLS 1.052,0.167 1.698,0.51 0.646,0.344 10 false DOWN 1.167,0.458 1.542,0.719 0.375,0.26 10 false UP
*a Component without harness connected
(Map Light Assembly (Sliding Roof Switch))


a.

Remove the map light assembly (sliding roof switch) (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UP) - 1 (GND) Tilt up switch pressed Below 1 Ω
5 (UP) - 1 (GND) Tilt up switch not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND) Tilt down switch pressed Below 1 Ω
4 (DOWN) - 1 (GND) Tilt down switch not pressed 10 kΩ or higher
3 (OPN) - 1 (GND) Slide open switch pressed Below 1 Ω
3 (OPN) - 1 (GND) Slide open switch not pressed 10 kΩ or higher
2 (CLS) - 1 (GND) Slide close switch pressed Below 1 Ω
2 (CLS) - 1 (GND) Slide close switch not pressed 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) - MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) - MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) AND BODY GROUND)
a.

Disconnect the S10 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


b.

Disconnect the U2 map light assembly (sliding roof switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-4 (UP) - U2-5 (UP) Always Below 1 Ω
S10-6 (DWN) - U2-4 (DOWN) Always Below 1 Ω
S10-7 (OPN) - U2-3 (OPN) Always Below 1 Ω
S10-5 (CLS) - U2-2 (CLS) Always Below 1 Ω
U2-1 (GND) - Body ground Always Below 1 Ω
S10-12 (E) - Body ground Always Below 1 Ω
S10-4 (UP) or U2-5 (UP) - Body ground Always 10 kΩ or higher
S10-6 (DWN) or U2-4 (DOWN) - Body ground Always 10 kΩ or higher
S10-7 (OPN) or U2-3 (OPN) - Body ground Always 10 kΩ or higher
S10-5 (CLS) or U2-2 (CLS) - Body ground Always 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR