This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2343 | The sliding roof drive gear sub-assembly has not been initialized. | ·
Sliding roof drive gear sub-assembly (Sliding roof ECU) ·
Map light assembly (Sliding roof switch) ·
Harness or connector |
When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).
Check that the sliding roof drive gear sub-assembly can be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).
The sliding roof drive gear sub-assembly can be initialized.
OK
NG
Clear the DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC B2343 is output | B |
A
B
| *a | Component without harness connected
(Map Light Assembly (Sliding Roof Switch)) |
Remove the map light assembly (sliding roof switch) (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (UP) - 1 (GND) | Tilt up switch pressed | Below 1 Ω |
| 5 (UP) - 1 (GND) | Tilt up switch not pressed | 10 kΩ or higher |
| 4 (DOWN) - 1 (GND) | Tilt down switch pressed | Below 1 Ω |
| 4 (DOWN) - 1 (GND) | Tilt down switch not pressed | 10 kΩ or higher |
| 3 (OPN) - 1 (GND) | Slide open switch pressed | Below 1 Ω |
| 3 (OPN) - 1 (GND) | Slide open switch not pressed | 10 kΩ or higher |
| 2 (CLS) - 1 (GND) | Slide close switch pressed | Below 1 Ω |
| 2 (CLS) - 1 (GND) | Slide close switch not pressed | 10 kΩ or higher |
OK
NG
Disconnect the S10 sliding roof drive gear sub-assembly (sliding roof ECU) connector.
Disconnect the U2 map light assembly (sliding roof switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S10-4 (UP) - U2-5 (UP) | Always | Below 1 Ω |
| S10-6 (DWN) - U2-4 (DOWN) | Always | Below 1 Ω |
| S10-7 (OPN) - U2-3 (OPN) | Always | Below 1 Ω |
| S10-5 (CLS) - U2-2 (CLS) | Always | Below 1 Ω |
| U2-1 (GND) - Body ground | Always | Below 1 Ω |
| S10-12 (E) - Body ground | Always | Below 1 Ω |
| S10-4 (UP) or U2-5 (UP) - Body ground | Always | 10 kΩ or higher |
| S10-6 (DWN) or U2-4 (DOWN) - Body ground | Always | 10 kΩ or higher |
| S10-7 (OPN) or U2-3 (OPN) - Body ground | Always | 10 kΩ or higher |
| S10-5 (CLS) or U2-2 (CLS) - Body ground | Always | 10 kΩ or higher |
OK
NG