Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2016.12
RM1440E _59 Vehicle Exterior _056167 SLIDING ROOF / CONVERTIBLE _0274174 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof ECU Power Source Circuit  


DESCRIPTION

If the sliding function and tilt function do not operate, there may be a malfunction in the sliding roof drive gear sub-assembly power source circuit.

WIRING DIAGRAM

B467742E01
3.646,3.448 6.167,3.802 2.521,0.354 10 false Sliding Roof Drive Gear Sub-assembly 3.646,3.271 4.188,3.615 0.542,0.344 10 false S10 3.958,1.656 4.74,2.167 0.781,0.51 10 false Sliding Roof ECU 5.333,0.875 6.604,1.302 1.271,0.427 10 false Sliding Roof Motor 2.177,0.896 2.875,1.229 0.698,0.333 10 false S/ROOF 0.813,0.708 1.833,1.083 1.021,0.375 10 false from Battery 0.313,1.302 1.719,1.698 1.406,0.396 10 false from IG1 No. 1 Relay 2.021,1.49 3.083,1.875 1.063,0.385 10 false ECU IG NO. 2 5.188,1.573 5.698,1.917 0.51,0.344 10 false Hall IC 5.188,2.302 5.698,2.646 0.51,0.344 10 false Hall IC 3.333,0.604 3.74,0.896 0.406,0.292 10 false B 3.333,1.198 3.74,1.49 0.406,0.292 10 false IG 3.344,1.813 3.75,2.104 0.406,0.292 10 false E 3.031,1.802 3.438,2.094 0.406,0.292 10 false 12 3.073,1.198 3.479,1.49 0.406,0.292 10 false 1 3.073,0.594 3.479,0.885 0.406,0.292 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) - BATTERY AND BODY GROUND)
a.
B467743C01
0.25,1.146 0.75,1.396 0.5,0.25 0.865,1.854 1.052,1.854 1.052,1.854 1.208,1.552 true 1.469,0.438 1.313,0.438 1.313,0.438 1.208,1.219 true 2.552,1.844 2.375,1.844 2.375,1.844 2.219,1.542 true 0.188,0.146 0.594,0.5 0.406,0.354 10 false *a 1.542,0.365 2.104,0.688 0.563,0.323 10 false IG 0.698,1.781 1.094,2.104 0.396,0.323 10 false B 2.635,1.76 3.031,2.083 0.396,0.323 10 false E 0.375,1.188 0.885,1.469 0.51,0.281 10 false S10
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU))


Disconnect the S10 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S10-8 (B) - Body ground Always 11 to 14 V
S10-1 (IG) - Body ground Ignition switch off Below 1 V
S10-1 (IG) - Body ground Ignition switch ON 11 to 14 V

Standard Resistance:
Tester Connection Condition Specified Condition
S10-12 (E) - Body ground Always Below 1 Ω




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR