Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC    P0021    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0022    Camshaft Position "A" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

The VVT system includes the ECM, camshaft timing oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E13


DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Valve timing cannot be adjusted when in the advance range (1 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve for intake camshaft
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM
P0012
P0022
Valve timing cannot be adjusted when in the retard range (2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve for intake camshaft
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller being stuck and stores a DTC.
  1. Example:
  2. A DTC is set when the following conditions "A" and "B" are met:
    1. It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").
    2. After the above condition is met, the camshaft timing oil control valve is forcibly activated for 10 seconds (Condition "B").
  3. DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve malfunctions or the presence of foreign objects in the camshaft timing oil control valve.

MONITOR STRATEGY


Related DTCs
P0011: Advanced camshaft timing (bank 1)
P0012: Retarded camshaft timing (bank 1)
P0021: Advanced camshaft timing (bank 2)
P0022: Retarded camshaft timing (bank 2)
Required Sensors/Components (Main)
Camshaft timing oil control valve and Camshaft timing gear assembly
Required Sensors/Components (Related)
Crankshaft position sensor, VVT sensor and Engine coolant temperature sensor
Frequency of Operation
continuous
Duration
Within 10 seconds
MIL Operation
Advanced camshaft timing: Immediate
Retarded camshaft timing: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0016, P0018 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
Battery voltage
11 V or higher
Engine speed
400 to 4000 rpm
Engine coolant temperature sensor
75°C (167°F) to 100°C (212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced Camshaft Timing 
Both of following conditions are met
-
Deviation of actual valve timing and target valve timing
5°CA (Crankshaft Angle)
Valve timing
No change at advanced valve timing

Retarded Camshaft Timing 
Both of following conditions are met
-
Deviation of actual valve timing and target valve timing
5°CA (Crankshaft Angle)
Valve timing
No change at retarded valve timing
If the difference between the target and actual camshaft timing is more than the specified value, the ECM operates the VVT actuator. Then, the ECM monitors the camshaft timing change for 5 seconds.

CONFIRMATION DRIVING PATTERN


A232050E03

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0011, P0012, P0021 or P0022.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  17. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  19. Perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE

HINT:
DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:

Abnormal bank
Timing Over-advanced
(Valve Timing is Out of Specified Range)
Timing Over-retarded
(Valve Timing is Out of Specified Range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is output, check the right bank VVT system for intake camshaft circuit (bank 1).
  2. Bank 1 refers to the bank that includes cylinder No. 1.
  3. If DTC P0021 or P0022 is output, check the left bank VVT system for intake camshaft circuit (bank 2).
  4. Bank 2 refers to the bank that does not include cylinder No. 1.
  5. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0011, P0012, P0021 or P0022
    A
    P0011, P0012, P0021 or P0022 and other DTCs
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Warm up the engine.

  1. Turn the Techstream on.

  1. Turn the A/C switch on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    0% (OFF)
    Normal engine speed
    127% (ON)
    Engine idles roughly or stalls
    (soon after camshaft timing oil control valve switched from OFF to ON)

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (Click here).



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read DTCs using the Techstream.

    OK:
    No DTC output.



NG
Go to step 4
OK

END 

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)


    A103826E11
  1. Remove the cylinder head cover RH and LH.
    Text in Illustration 
    *1
    Timing Mark

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft timing oil control valve assembly .



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER AND PIPE
A225778E01
  1. Remove the oil pipe No. 1 or No. 2.
    Text in Illustration 
    *1
    No. 1 Oil Pipe
    *2
    No. 2 Oil Pipe

  1. Remove the OCV filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.

  1. Reinstall the OCV filter.

  1. Reinstall the oil pipe No. 1 or No. 2.



NG
REPLACE OIL CONTROL VALVE FILTER AND PIPE (Click here)
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream.

  1. Drive the vehicle for more than 10 minutes.

  1. Read output DTCs using the Techstream.

    OK:
    No DTC output.

    HINT:
    DTC P0011, P0012, P0021 or P0022 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

SYSTEM OK