DTC P2119 Throttle Actuator Control Throttle Body Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2119 | Throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic). |
|
| Related DTCs | P2119: ETCS malfunction |
| Required Sensors/Components (Main) | Throttle actuator |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | Within 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| System guard* judge condition | ON |
| *: System guard set when following conditions are met: | - |
| Throttle actuator | ON |
| Throttle actuator duty calculation | Executing |
| Throttle position sensor fail | Not detected |
| Throttle actuator current-cut operation | Not executing |
| Throttle actuator power supply | 4 V or higher |
| Throttle actuator fail | Not detected |
| Either of following conditions A or B met | - |
| A. Difference between commanded closed throttle position and current closed throttle position | 0.3 V or more |
| B. Difference between commanded open throttle position and current open throttle position | 0.3 V or more |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2119 | A |
| P2119 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.
Check the values displayed on the tester while fully depressing and releasing the accelerator pedal quickly.
| Result | Proceed to |
| Throttle Position No. 1 does not change | A |
| Throttle Position No. 1 changes even a little | B |
|
| ||||
| A | |
| 3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
Inspect the throttle body with motor assembly .
|
| ||||
| OK | |
| 4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle body. Also, check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 5.READ VALUE USING TECHSTREAM (THROTTLE POSITION) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.
Check the values displayed on the tester while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output* | A |
| Other than above | B |
|
| ||||
| OK | |
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY WITH MOTOR ASSEMBLY) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
| NEXT | ||
| ||
| 7.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY |
Replace the throttle body assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Allow the engine to idle for 15 seconds or more.
Fully depress and release the accelerator pedal several times quickly.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| Not DTC is output | A |
| P2119 is output | B |
|
| ||||
| OK | ||
| ||