Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.
The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.5 V in proportion to the amount the accelerator pedal is depressed (throttle valve opening angle). The signal from VPA indicates the actual accelerator pedal position (throttle valve opening angle) and is used for engine control. The signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.
The ECM monitors the actual accelerator pedal position (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.


A112620E47


DTC No.
DTC Detection Condition
Trouble Area
P2120
VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
  1. Accelerator pedal sensor assembly
  1. ECM
P2122
VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
  1. Accelerator pedal sensor assembly
  1. Open in VCPA circuit
  1. Open or ground short in VPA circuit
  1. ECM
P2123
VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
  1. Accelerator pedal sensor assembly
  1. Open in EPA circuit
  1. ECM
P2125
VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
  1. Accelerator pedal sensor assembly
  1. ECM
P2127
VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection logic).
  1. Accelerator pedal sensor assembly
  1. Open in VCP2 circuit
  1. Open or ground short in VPA2 circuit
  1. ECM
P2128
Conditions (a) and (b) are met for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
  1. Accelerator pedal sensor assembly
  1. Open in EPA2 circuit
  1. ECM
P2138
Condition (a) or (b) is met for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
  1. Short between VPA and VPA2 circuits
  1. Accelerator pedal sensor assembly
  1. ECM

HINT:
When any of these DTCs are output, check the accelerator pedal position sensor voltage by entering the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area
Accel Sensor Out No.1
When Accelerator Pedal Released
Accel Sensor Out No.2
When Accelerator Pedal Released
Accel Sensor Out No.1
When Accelerator Pedal Depressed
Accel Sensor Out No.2
When Accelerator Pedal Depressed
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
Open or ground short in VPA circuit
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 4.7 V
Open or ground short in VPA2 circuit
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
Normal condition
0.5 to 1.1 V
1.2 to 2.0 V
2.6 to 4.5 V
3.4 to 4.7 V

HINT:
Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When the output voltage of either VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is less than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.
If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P2120: Accelerator pedal position sensor 1 range check (fluctuating)
P2122: Accelerator pedal position sensor 1 range check (low voltage)
P2123: Accelerator pedal position sensor 1 range check (high voltage)
P2125: Accelerator pedal position sensor 2 range check (fluctuating)
P2127: Accelerator pedal position sensor 2 range check (low voltage)
P2128: Accelerator pedal position sensor 2 range check (high voltage)
P2138: Accelerator pedal position sensor range check (correlation)
Required Sensors/Components (Main)
Accelerator pedal position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds: P2120, P2122, P2125 and P2127
2.0 seconds: P2123, P2128 and P2138
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P2120 
Either of following conditions 1 or 2 met:
-
1. VPA voltage when VPA2 voltage 0.04 V or higher
0.4 V or less
2. VPA voltage
4.8 V or higher

P2122 
VPA voltage when VPA2 voltage 0.04 V or higher
0.4 V or less

P2123 
VPA voltage
4.8 V or higher

P2125 
Either of following conditions 1 or 2 met:
-
1. VPA2 voltage when VPA voltage 0.04 V or higher
1.2 V or less
2. VPA2 voltage when VPA voltage 0.4 to 3.45 V
4.8 V or higher

P2127 
VPA2 voltage when VPA voltage 0.04 V or higher
1.2 V or less

P2128 
VPA2 voltage when VPA voltage 0.4 to 3.45 V
4.8 V or higher

P2138 
Either of following conditions A or B met:
-
Condition A
-
Difference between VPA and VPA2 voltages
0.02 V or less
Condition B
-
VPA voltage
0.4 V or less
VPA2 voltage
1.2 V or less

COMPONENT OPERATING RANGE


VPA voltage
0.4 to 4.8 V
VPA2 voltage
1.2 to 4.8 V
Difference between VPA and VPA2 voltages
More than 0.02 V

CONFIRMATION DRIVING PATTERN


A199317E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Fully depress and release the accelerator pedal [B].
  7. Check that 5 seconds or more have elapsed since the DTCs were cleared.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM


A227105E01


INSPECTION PROCEDURE

HINT:
  1. These DTCs relate to the accelerator pedal position sensor.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2)
A208621E02
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

  1. Read the value displayed on the Techstream.

    Standard Voltage:
    Accelerator Pedal Operation
    Accel Sensor Out No.1
    Accel Sensor Out No.2
    Difference between Accel Sensor Out No.1 and Accel Sensor Out No.2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    More than 0.02 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.7 V

    Text in Illustration 
    *a
    Depressed
    *b
    Released



OK
Go to step 5

NG
Go to step 2

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A3-6 (VPA) - F50-6 (VPA)
    Always
    Below 1 Ω
    A3-5 (EPA) - F50-3 (EPA)
    Always
    Below 1 Ω
    A3-4 (VCPA) - F50-4 (VCPA)
    Always
    Below 1 Ω
    A3-3 (VPA2) - F50-5 (VPA2)
    Always
    Below 1 Ω
    A3-2 (EPA2) - F50-1 (EPA2)
    Always
    Below 1 Ω
    A3-1 (VCP2) - F50-2 (VCP2)
    Always
    Below 1 Ω
    A3-6 (VPA) or F50-6 (VPA) - Body ground
    Always
    10 kΩ or higher
    A3-5 (EPA) or F50-3 (EPA) - Body ground
    Always
    10 kΩ or higher
    A3-4 (VCPA) or F50-4 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A3-3 (VPA2) or F50-5 (VPA2) - Body ground
    Always
    10 kΩ or higher
    A3-2 (EPA2) or F50-1 (EPA2) - Body ground
    Always
    10 kΩ or higher
    A3-1 (VCP2) or F50-2 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal sensor assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK ECM (VCPA AND VCP2 VOLTAGE)
A200914E13
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A3-4 (VCPA) - A3-5 (EPA)
    Ignition switch ON
    4.5 to 5.5 V
    A3-1 (VCP2) - A3-2 (EPA2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Accelerator Pedal Sensor Assembly)

  1. Reconnect the accelerator pedal sensor assembly connector.



NG
REPLACE ECM (Click here)
OK


4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
  1. Replace the accelerator pedal sensor assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)