Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
  1. (a) Vehicle speed is 20 km/h (12.4 mph) or more.
  2. (b) Engine speed is 1000 rpm or more.
  3. (c) STA signal is on.
  1. Park/neutral position switch
  2. Starter relay (ST) circuit
  3. Ignition switch (w/o Smart Key System)
  4. Power management control ECU (w/ Smart Key System)
  5. ECM

MONITOR STRATEGY


Related DTCs
P0617: Starter signal
Required Sensors/Components (Main)
Starter relay, Park/neutral position switch and Ignition switch or Power management control ECU
Required Sensors/Components (Related)
Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or higher
Vehicle speed
20 km/h (12.43 mph) or more
Engine speed
1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

CONFIRMATION DRIVING PATTERN


A231469E04

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Idle the engine for 5 seconds or more [B].
  7. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read the DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0617.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].

  13. Check the DTC judgment result [E].
  14. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A227112E01


A227113E01


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
    If the engine does not crank, proceed to Problem Symptoms Table (Click here).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the value displayed on the Techstream when the ignition switch is turned to ON and the engine is started.

    OK:

    Condition
    Starter Signal
    Ignition switch turned to ON
    OFF
    Engine started
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly for 4WD .

  1. Inspect the park/neutral position switch assembly for 2WD .



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STA TERMINAL OF ECM)

NEXT


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
END
A

REPLACE ECM (Click here)