Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Auxiliary battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU) (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH open
    Below 1 V
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH closed
    11 to 14 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH open
    Below 1 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH closed
    11 to 14 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    11 to 14 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    11 to 14 V
    F9-11 (L2) - Body ground
    LG - Body ground
    Driver side door key-linked lock input
    Driver side door key cylinder lock position
    Below 1 V
    F9-11 (L2) - Body ground
    LG - Body ground
    Driver side door key-linked lock input
    Ignition switch off, all doors closed and driver side door key cylinder neutral position
    Pulse generation (see waveform 1 or 2)
    F9-24 (UL3) - Body ground
    GR - Body ground
    Driver side door key-linked unlock input
    Driver side door key cylinder unlock position
    Below 1 V
    F9-24 (UL3) - Body ground
    GR - Body ground
    Driver side door key-linked unlock input
    Ignition switch off, all doors closed and driver side door key cylinder neutral position
    Pulse generation (see waveform 3 or 4)
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Front door LH unlocked
    Below 1 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Ignition switch off, all doors closed and front door LH locked
    Pulse generation (see waveform 5 or 6)
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Front door RH unlocked
    Below 1 V
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Ignition switch off, all doors closed and front door RH locked
    Pulse generation (see waveform 7 or 8)
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Ignition switch off, all doors closed and rear door LH locked
    Pulse generation (see waveform 9 or 10)
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Ignition switch off, all doors closed and rear door RH locked
    Pulse generation (see waveform 11 or 12)
    2B-34 (IND) - Body ground
    L - Body ground
    Security indicator light signal
    Security indicator light illuminates (illuminates only for 30 (+/-5) seconds in alarm sounding state (blinks when system in armed state))
    3 to 6 V
    2D-23 (HCTY) - Body ground
    B - Body ground
    Security courtesy switch input
    Engine hood open
    Below 1 V
    2D-23 (HCTY) - Body ground
    B - Body ground
    Security courtesy switch input
    Engine hood closed
    Pulse generation (see waveform 13 or 14)
    2D-29 (HORN) - Body ground
    GR-L - Body ground
    Vehicle horn(s) signal
    Vehicle horn(s) sounding (theft warning system in alarm sounding state)
    Pulse generation
    2D-29 (HORN) - Body ground
    GR-L - Body ground
    Vehicle horn(s) signal
    Vehicle horn(s) not sounding (theft warning system in armed state)
    11 to 14 V
    2D-25 (SH) - Body ground
    R - Body ground
    Security horn signal
    Security horn sounding (theft warning system in alarm sounding state)
    Pulse generation
    2D-25 (SH) - Body ground
    R - Body ground
    Security horn signal
    Security horn not sounding (theft warning system in armed state)
    11 to 14 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



  5. B201885E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder neutral position



  7. B201886E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder neutral position



  9. B201885E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-24 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder neutral position



  11. B201886E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-24 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder neutral position



  13. B199631E01
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  15. B199632E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  17. B201885E01
  18. Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  19. B201886E01
  20. Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  21. B201885E01
  22. Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  23. B201886E01
  24. Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  25. B201885E01
  26. Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked



  27. B201886E01
  28. Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked



  29. B201885E01
  30. Using an oscilloscope, check waveform 13.
    Waveform 13 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2D-23 (HCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and engine hood closed



  31. B201886E01
  32. Using an oscilloscope, check waveform 14.
    Waveform 14 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2D-23 (HCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and engine hood closed


CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B241165E01

  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the V2 multiplex network door ECU (back door P/W) connector.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door closed
    Pulse generation (see waveform 1 or 2)
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door open
    Below 1 V
    W10-16 (BKL) - W10-8 (KEYE)*
    P - V
    Tail gate control switch lock input
    Back door lock key cylinder neutral position
    Pulse generation (see waveform 3 or 4)
    W10-16 (BKL) - W10-8 (KEYE)*
    P - V
    Tail gate control switch lock input
    Back door lock key cylinder is turned lock
    Below 1 V
    W10-15 (BKUL) - W10-8 (KEYE)*
    R - V
    Tail gate control switch unlock input
    Back door lock key cylinder neutral position
    Pulse generation (see waveform 3 or 4)
    W10-15 (BKUL) - W10-8 (KEYE)*
    R - V
    Tail gate control switch unlock input
    Back door lock key cylinder is turned unlock
    Below 1 V

    1. *: w/o Smart Key System
    If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.



  5. B245381E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  7. B245382E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  9. B245381E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. W10-16 (BKL) - W10-8 (KEYE)
    2. W10-15 (BKUL) - W10-8 (KEYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door lock key cylinder neutral position



  11. B245382E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. W10-16 (BKL) - W10-8 (KEYE)
    2. W10-15 (BKUL) - W10-8 (KEYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door lock key cylinder neutral position