DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0705 | One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
|
|
| Related DTCs | P0705: Park/neutral position switch/Verify switch input |
| Required sensors/Components | Park/neutral position switch |
| Frequency of operation | Continuous |
| Duration | Condition (A) and (B) 2 sec. Condition (C) 60 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | None |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| P switch | ON |
| N switch | ON |
| NSW switch | ON |
| R switch | ON |
| D switch | ON |
| P switch | ON |
| N switch | ON |
| NSW switch | ON |
| R switch | ON |
| P switch | OFF |
| N switch | OFF |
| NSW switch | OFF |
| R switch | OFF |
| D switch | OFF |
| Park/neutral position switch | The park/neutral position switch sends only one signal to the ECM |

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect. |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect. |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect. |
| Shift SW Status (N Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect. |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or shift cable maybe incorrect. |
| 1.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Disconnect the F76 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG) - 7 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever not in S, "+" or "-" | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Control Switch) |
|
| ||||
| OK | |
| 2.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE) |
![]() |
Disconnect the F76 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F76-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| F76-3 (IG) - Body ground | Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Transmission Control Switch) |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the B42 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift lever in P | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever in N | Below 1 Ω |
| 2 (RB) - 7 (DL) |
| Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | 10 kΩ or higher |
| Shift lever not in N | 10 kΩ or higher |
| 2 (RB) - 7 (DL) |
| 10 kΩ or higher |
| *a | Component without harness connected (Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the B42 park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B42-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| B42-2 (RB) - Body ground | Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the B36 and B37 ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B36-35 (P) - Body ground |
| 11 to 14 V |
| B36-28 (R) - Body ground |
| 11 to 14 V* |
| B36-29 (N) - Body ground |
| 11 to 14 V |
| B36-27 (D) - Body ground |
| 11 to 14 V |
| B37-2 (NSW) - Body ground |
| 11 to 14 V |
| B36-35 (P) - Body ground |
| Below 1 V |
| B36-28 (R) - Body ground |
| Below 1 V |
| B36-29 (N) - Body ground |
| Below 1 V |
| B36-27 (D) - Body ground |
| Below 1 V |
| B37-2 (NSW) - Body ground |
| Below 1 V |
| *a | Rear view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
![]() |
Disconnect the F50 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F50-24 (S) - Body ground | Shift lever in S, "+" or "-" | 11 to 14 V |
| F50-24 (S) - Body ground | Shift lever not in S, "+" or "-" | Below 1 V |
| *a | Rear view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||