DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0015 Camshaft Position "B" - Timing Over-Retarded (Bank 1) |
DTC P0024 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0025 Camshaft Position "B" - Timing Over-Retarded (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0014 P0024 | Exhaust valve timing is not adjusted in the advance range (2 trip detection logic). |
|
| P0015 P0025 | Exhaust valve timing is not adjusted in the retard range (1 trip detection logic). |
|
| Related DTCs | P0014: Advanced camshaft timing (bank 1) P0015: Retarded camshaft timing (bank 1) P0024: Advanced camshaft timing (bank 2) P0025: Retarded camshaft timing (bank 2) |
| Required sensors/components (Main) | Camshaft timing oil control valve and VVT Actuator |
| Required sensors/components (Related) | Crankshaft position sensor, VVT sensor and Engine coolant temperature sensor |
| Frequency of operation | Continuous |
| Duration | Within 10 seconds |
| MIL operation | Advanced camshaft timing: 2 driving cycles Retarded camshaft timing: Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs are not present | P0013, P0023 (Exhaust VVT Oil Control Valve) P0017, P0019 (Exhaust VVT System - Misalignment) P0102, P0103 (Mass Air Flow Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) |
| Battery voltage | 11 V or higher |
| Engine speed | 500 to 4000 rpm |
| Engine coolant temperature | 75 to 100°C (167 to 212°F) |
| Both conditions are met: | - |
| Deviation of actual valve timing and target valve timing | More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
| Valve timing | No change at advanced valve timing |
| Both conditions are met: | - |
| Deviation of actual valve timing and target valve timing | More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
| Valve timing | No change at retarded valve timing |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Abnormal bank | Timing Over-advanced (Valve Timing is Out of Specified Range) | Timing Over-retarded (Valve Timing is Out of Specified Range) |
| Bank 1 | P0014 | P0015 |
| Bank 2 | P0024 | P0025 |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0014, P0015, P0024 or P0025 | A |
| P0014, P0015, P0024 or P0025 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE) |
Connect the Techstream to the DLC3.
Start the engine.
Warm up the engine.
Turn the Techstream on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve using the Techstream.
| Techstream Operation | Specified Condition |
| 0% (OFF) | Normal engine speed |
| 127% (ON) | Engine idles roughly or stalls (soon after camshaft timing oil control valve switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Clear DTCs (Click here).
Warm up the engine.
Switch the ECM from normal mode to check mode using the Techstream (Click here).
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read DTCs using the Techstream.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH) |
![]() |
Remove the cylinder head cover RH and LH.
| *1 | Timing Mark |
Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.
Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
Reinstall the cylinder head cover RH and LH.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (CAMSHAFT TIMING OIL CONTROL VALVE FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly .
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER AND PIPE |
![]() |
Remove the oil pipe No. 1 or No. 2.
| *1 | No. 1 Oil Pipe |
| *2 | No. 2 Oil Pipe |
Remove the oil control valve filter.
Check that the filter and pipe are not clogged.
Reinstall the oil control valve filter.
Reinstall the oil pipe No. 1 or No. 2.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Clear DTCs.
Warm up the engine.
Switch the ECM from normal mode to check mode using the Techstream (Click here).
Drive the vehicle for more than 10 minutes or more.
Read output DTCs using the Techstream.
|
| ||||
| OK | ||
| ||