DTC C1405 Open or Short in Front Speed Sensor RH Circuit |
DTC C1406 Open or Short in Front Speed Sensor LH Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1405 C1406 | Either condition is met:
|
|

| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | Front speed sensor RH open detection/ Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open detection/ Error or Normal | Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1405 and C1406 are not output | A |
| DTCs C1405 and/or C1406 are output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT SKID CONTROL SENSOR WIRE |
Remove the skid control sensor wire (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Az2-1 - z5-1 (FR-) | Always | Below 1 Ω |
| Az2-2 - z5-2 (FR+) | Always | Below 1 Ω |
| Az2-1 - Az2-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| Az3-1 - z6-1 (FL-) | Always | Below 1 Ω |
| Az3-2 - z6-2 (FL+) | Always | Below 1 Ω |
| Az3-1 - Az3-2 | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *1 | Skid Control Sensor Wire |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A6 skid control ECU connector.
Disconnect the z5 and/or z6 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-3 (FR+) - z5-2 (FR+) | Always | Below 1 Ω |
| A6-3 (FR+) - Body ground | Always | 10 kΩ or higher |
| A6-17 (FR-) - z5-1 (FR-) | Always | Below 1 Ω |
| A6-17 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A6-18 (FL+) - z6-2 (FL+) | Always | Below 1 Ω |
| A6-18 (FL+) - Body ground | Always | 10 kΩ or higher |
| A6-4 (FL-) - z6-1 (FL-) | Always | Below 1 Ω |
| A6-4 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK TERMINAL VOLTAGE (FR+, FL+) |
Disconnect the z5 and/or z6 front speed sensor connector.
Connect the A6 skid control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z5-2 (FR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| z6-2 (FL+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Front Speed Sensor) |
|
| ||||
| OK | ||
| ||