DTC C1425 Open in Stop Light Switch Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1425 | When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off, an open in the stop light switch circuit continues for 3 seconds or more. |
|

| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (STOP LIGHT SW) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the Data List on the Techstream (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch assembly / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the Stop Light SW display observed on the Techstream changes according to brake pedal operation.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch to ON.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1425 is not output. | A |
| DTC C1425 is output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK STOP LIGHT SWITCH ASSEMBLY |
Check the stop light switch assembly (Click here).
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A6 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-7 (STP) - Body ground | Stop light switch assembly ON (Brake pedal depressed) | 11 to 14 V |
| A6-7 (STP) - Body ground | Stop light switch assembly OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
|
| ||||
| OK | |
| 6.RECONFIRM DTC |
Reconnect the A6 skid control ECU connector.
Clear the DTCs (Click here).
Turn the ignition switch to ON.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1425 is not output. | A |
| DTC C1425 is output. | B |
|
| ||||
| A | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A6 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-7 (STP) - Body ground | Stop light switch assembly ON (Brake pedal depressed) | 11 to 14 V |
| A6-7 (STP) - Body ground | Stop light switch assembly OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
|
| ||||
| OK | ||
| ||