Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > TEST MODE PROCEDURE

for Preparation Click here



PERFORM SIGNAL CHECK

HINT:
  1. When entering signal check mode, the tire pressure warning ECU stores all the signal check DTCs first. After completing the signal check for each inspection item, the DTCs for systems that are determined to be normal by the tire pressure warning ECU are cleared.
  2. The DTCs for other inspection items may not be cleared when only a certain signal is inspected.
  3. When signal check returns to normal mode, all the signal check DTCs are cleared.

  1. Turn the ignition switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the Techstream on.

  5. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    HINT:
    Every time the test mode DTC clear conditions are satisfied, the tire pressure warning light turns on for 1 second. Then, the tire pressure warning light blinks at 0.125 second intervals.

  6. Start the engine and allow it to run at 1000 rpm for 3 seconds or more to check the engine speed signal (C2194/94).

  7. Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

  8. Loosen the valve core and rapidly reduce the pressure by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds to check the transmitter data (C2181/81 to C2184/84).

    HINT:
    The transmitter ID can be transmitted by rapidly reducing the tire pressure.

  9. Check that the tire pressure warning system test mode DTCs are cleared.

    Test Mode DTC
    Test Signal
    Test Mode DTC Clear Condition
    C2181/81 to C2184/84
    Transmitter Data
    Receive data from transmitter which has registered ID in tire pressure warning ECU
    C2191/91
    Vehicle Speed Signal
    Vehicle speed of 20 km/h (12 mph) or more is detected for 3 seconds or more
    C2194/94
    Engine Speed Signal
    Engine speed of 1000 rpm or more is detected for 3 seconds or more

  10. Result

    HINT:
    After the signal check is completed, check for test mode (signal check mode) DTCs to confirm the system status.


    Condition
    Procedure
    Test mode DTC is output
    Repair faulty part and enter Signal Check again
    Test mode DTCs are cleared
    No problem

  11. End of test mode (signal check mode)

    1. After completing test mode (Signal Check mode), turn the ignition switch off and disconnect the Techstream.

  12. Test mode (signal check mode) DTCs

    1. If a trouble code is output during the test mode (signal check mode) DTC check, check the diagnosis procedure listed for that code. For details of each code, refer to "See page" below.

      DTC Code
      Detection Item
      Trouble Area
      See page
      C2181/81
      Transmitter ID1 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here
      C2182/82
      Transmitter ID2 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here
      C2183/83
      Transmitter ID3 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here
      C2184/84
      Transmitter ID4 not received
      1. Tire pressure warning valve and transmitter
      2. Tire pressure warning antenna and receiver
      3. Harness or connector
      4. Tire pressure warning ECU
      Click here
      C2191/91
      Vehicle speed signal error
      1. Vehicle speed signal circuit
      2. Combination meter assembly
      3. Tire pressure warning ECU
      Click here
      C2194/94
      Engine speed signal error
      1. ECM
      2. Harness or connector
      3. Tire pressure warning ECU
      Click here