Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2240    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1)

DTC    P2241    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1)

DTC    P2242    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)

DTC    P2255    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1)

DTC    P2256    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1)

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2237
P2240
Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2238
P2241
  1. Case 1:
Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic):
(a) AF+ voltage is 0.5 V or less.
(b) (AF+) - (AF-) is 0.1 V or less.
  1. Case 2:
Air fuel ratio sensor admittance is below 0.022 1/Ω (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2239
P2242
AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2252
P2255
AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P2253
P2256
AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM

HINT:
  1. DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 air fuel ratio sensor circuit.
  2. DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 air fuel ratio sensor circuit.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.


MONITOR DESCRIPTION

The air fuel ratio sensor varies its output voltage in proportion to the air-fuel ratio. If the air fuel ratio sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the air fuel ratio sensor circuit.

MONITOR STRATEGY


Related DTCs
P2237: Air fuel ratio sensor (bank 1) open circuit between AF+ and AF-
P2238: Air fuel ratio sensor (bank 1) low impedance
P2238: Air fuel ratio sensor (bank 1) short circuit between AF+ and GND
P2239: Air fuel ratio sensor (bank 1) short circuit between AF+ and +B
P2252: Air fuel ratio sensor (bank 1) short circuit between AF- and GND
P2253: Air fuel ratio sensor (bank 1) short circuit between AF- and +B
P2240: Air fuel ratio sensor (bank 2) open circuit between AF+ and AF-
P2241: Air fuel ratio sensor (bank 2) low impedance
P2241: Air fuel ratio sensor (bank 2) short circuit between AF+ and GND
P2242: Air fuel ratio sensor (bank 2) short circuit between AF+ and +B
P2255: Air fuel ratio sensor (bank 2) short circuit between AF- and GND
P2256: Air fuel ratio sensor (bank 2) short circuit between AF- and +B
Required Sensors/Components (Main)
Air fuel ratio sensor
Required Sensors/Components (Related)
Engine coolant temperature sensor, Crankshaft position sensor
Frequency of Operation
Continuous
Duration
10 seconds: Air fuel ratio sensor open circuit between AF+ and AF- and low impedance
5 seconds: Other
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2237, P2238, P2240 and P2241 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P0505 (IAC valve)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary Air Injection System)
P219A, P219B (Air-Fuel Ratio Imbalance)

P2237 and P2240 (Open Circuit between AF+ and AF-) 
Estimated sensor temperature
450 to 550°C (842 to 1022°F)
Engine
Running
Battery voltage
11 V or higher

P2238 and P2241 (Low Impedance) 
Estimated sensor temperature
700 to 800°C (1292 to 1472°F)
Engine coolant temperature
5°C (41°F) or higher (varies with ECT at engine start)
Fuel cut
Not executed

P2238 and P2241 (Short Circuit between AF+ and GND) 
Battery voltage
11 V or higher
Ignition switch
ON
Time after ignition switch is turned from off to ON
5 seconds or more

P2238 and P2241 (Short Circuit between AF+ and AF-) 
Battery voltage
11 V or higher
Ignition switch
ON
Time after ignition switch is turned from off to ON
5 seconds or more

P2239 and P2242 (Short Circuit between AF+ and +B) 
Battery voltage
11 V or higher
Ignition switch
ON
Time after ignition switch is turned from off to ON
5 seconds or more

P2252 and P2255 (Short Circuit between AF- and GND) 
Battery voltage
11 V or higher
Ignition switch
ON
Time after ignition switch is turned from off to ON
5 seconds or more

P2253 and P2256 (Short Circuit between AF- and +B) 
Battery voltage
11 V or higher
Ignition switch
ON
Time after ignition switch is turned from off to ON
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P2237 and P2240 (Open Circuit between AF+ and AF-) 
Air fuel ratio sensor admittance
Below 0.002 1/Ω

P2238 and P2241 (Low Impedance) 
Air fuel ratio sensor admittance
Below 0.074 1/Ω

P2238 and P2241 (Short Circuit between AF+ and GND) 
AF+ terminal voltage
0.5 V or less

P2238 and P2241 (Short Circuit between AF+ and AF-) 
Difference between AF+ and AF- terminal voltages
0.1 V or less

P2239 and P2242 (Short Circuit between AF+ and +B) 
AF+ terminal voltage
Higher than 4.5 V

P2252 and P2255 (Short Circuit between AF- and GND) 
AF- terminal voltage
0.5 V or less

P2253 and P2256 (Short Circuit between AF- and +B) 
AF- terminal voltage
Higher than 4.5 V

CONFIRMATION DRIVING PATTERN


A199234E02

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and wait 2 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. Although the DTC titles say heated oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

HINT:
Techstream only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
  1. (a) Connect the Techstream to the DLC3.
  2. (b) Start the engine and turn the Techstream on.
  3. (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
  5. (e) Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in fine gradations.
  2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
12.5%
Rich
Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
12.5%
Rich
Higher than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Below 0.4 V

NOTICE:
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E11
A151324E08
A150787E11
A150788E06
-
2
A150787E11
A150790E01
A150787E11
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E11
A151324E08
A150787E11
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E11
A150790E01
A150787E11
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the output voltages of both the air fuel ratio and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 or AFS Voltage B2S1, and O2S B1S2 or O2S B2S2. Then press the graph button on the Data List display.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B26-1 (HA1A) - B39-17 (HA1A)
    Always
    Below 1 Ω
    B26-3 (A1A+) - B38-1 (A1A+)
    Always
    Below 1 Ω
    B26-4 (A1A-) - B38-2 (A1A-)
    Always
    Below 1 Ω
    B27-1 (HA2A) - B39-19 (HA2A)
    Always
    Below 1 Ω
    B27-3 (A2A+) - B38-7 (A2A+)
    Always
    Below 1 Ω
    B27-4 (A2A-) - B38-8 (A2A-)
    Always
    Below 1 Ω
    B26-1 (HA1A) or B39-17 (HA1A) - Body ground
    Always
    10 kΩ or higher
    B26-3 (A1A+) or B38-1 (A1A+) - Body ground
    Always
    10 kΩ or higher
    B26-4 (A1A-) or B38-2 (A1A-) - Body ground
    Always
    10 kΩ or higher
    B27-1 (HA2A) or B39-19 (HA2A) - Body ground
    Always
    10 kΩ or higher
    B27-3 (A2A+) or B38-7 (A2A+) - Body ground
    Always
    10 kΩ or higher
    B27-4 (A2A-) or B38-8 (A2A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the air fuel ratio sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3.PERFORM CONFIRMATION DRIVING PATTERN
  1. Drive the vehicle according to Confirmation Driving Pattern.


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.

  1. Read pending DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    No output
    A
    P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256
    B



B
REPLACE ECM (Click here)
A

END