Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU) (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH open
    Below 1 V
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH closed
    11 to 14 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH open
    Below 1 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH closed
    11 to 14 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    11 to 14 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    11 to 14 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Front door LH unlocked
    Below 1 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Engine switch off, all doors closed and front door LH locked
    Pulse generation (see waveform 1 or 2)
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Front door RH unlocked
    Below 1 V
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Engine switch off, all doors closed and front door RH locked
    Pulse generation (see waveform 3 or 4)
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Engine switch off, all doors closed and rear door LH locked
    Pulse generation (see waveform 5 or 6)
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Engine switch off, all doors closed and rear door RH locked
    Pulse generation (see waveform 7 or 8)
    2D-13 (BZR) - Body ground
    GR - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    2D-13 (BZR) - Body ground
    GR - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer on
    11 to 14 V
    F9-3 (HAZ) - Body ground
    W - Body ground
    Hazard warning signal light signal output
    Hazard warning signal switch off
    Below 1 V
    F9-3 (HAZ) - Body ground
    W - Body ground
    Hazard warning signal light signal output
    Hazard warning signal switch on
    11 to 14 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



  5. B199631E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  7. B199632E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  9. B201885E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  11. B201886E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  13. B201885E01
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  15. B201886E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  17. B201885E01
  18. Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked



  19. B201886E01
  20. Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked


CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B241165E01

  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Engine switch power supply
    Engine switch off
    Below 1 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the V2 multiplex network door ECU (back door P/W) connector.

  4. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door closed
    Pulse generation (see waveform 1 or 2)
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door open
    Below 1 V
    If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.



  5. B245381E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  7. B245382E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed


CHECK CERTIFICATION ECU

B203498E28

  1. Disconnect the F79 certification ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F79-1 (+B) - F79-15 (E)
    V - W-B
    +B power supply
    Always
    11 to 14 V
    F79-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F79-16 (IG) - F79-15 (E)
    W - W-B
    IG power supply
    Engine switch off → Engine switch on (IG)
    Below 1 V → 11 to 14 V
    F79-17 (CUTB) - F79-15 (E)
    L - W-B
    +B power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the F79 certification ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F78-5 (RCO) - F79-15 (E)
    L - W-B
    Door control receiver power source
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 4.5 to 5.5 V
    F78-15 (RDA) - F79-15 (E)
    G - W-B
    Door control receiver data input signal
    Engine switch off
    11 to 14 V pulse generation at regular intervals
    F78-16 (RSSI) - F79-15 (E)
    P - W-B
    Door control receiver electric wave existence signal
    All doors locked, all doors closed and transmitter switch not pressed → pressed
    11 to 14 V → Below 2 V

    1. If the result is not as specified, the certification ECU may have a malfunction.