Home › Drivetrain · VF2BM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > INSPECTION

for Preparation Click here



1. TRANSFER SYSTEM

NOTICE:
  1. Switch the transfer position switch when the A/T shift lever is in N and the vehicle speed is 5 km/h or less.
  2. Do not change from H2 to H4 when the vehicle speed is 100 km/h or more.



2. INSPECT INDICATOR LIGHT
  1. 4WD Indicator Light:

    1. Start the engine.

    2. Change the transfer position switch from the H2 to H4.

    3. Check that the 4WD indicator light illuminates.

      OK:
      4WD indicator light comes on or 4WD indicator light comes on after blinking.

      If the result is not as specified, inspect the transfer indicator switch (4WD position) and four wheel drive control ECU. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (Click here). Then check the combination meter (Click here).

  1. 4LO Indicator Light:

    1. Turn the ignition switch to ON.

    2. Move the shift lever to N (vehicle is stopped).

    3. Change the transfer position switch from H4 to L4.

    4. Check the 4LO indicator light.

      OK:
      4LO indicator light comes on or 4LO indicator light comes on after blinking.

      If the result is not as specified, inspect the transfer indicator switch (L4 position) and four wheel drive control ECU. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (Click here). Then check the combination meter (Click here).



3. INSPECT FOUR WHEEL DRIVE CONTROL ECU (POWER SUPPLY)


    C217417E24
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F46-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Four Wheel Drive Control ECU)
    If the result is not as specified, inspect the fuse, harness or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F46-4 (GND) - Body ground
    Always
    Below 1 Ω

    If the result is not as specified, repair or replace the harness, fuse or connector.



4. INSPECT FOUR WHEEL DRIVE CONTROL ECU (TRANSFER INDICATOR SWITCH)


    C217417E25
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F47-16 (4WDL) - Body ground
    Ignition switch ON
    Transfer shift lever position H2 or H4
    10 to 14 V
    Ignition switch ON
    Transfer shift lever position L4
    Below 1.5 V
    F47-3 (4WD) - Body ground
    Ignition switch ON
    Transfer shift lever position H2
    10 to 14 V
    Ignition switch ON
    Transfer shift lever position H4, L4
    Below 1.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Four Wheel Drive Control ECU)
    If the result is not as specified, check the power supply. If the power supply is normal, inspect the transfer indicator switch (Click here).



5. CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - TRANSFER INDICATOR SWITCH)


  1. Check the transfer indicator switch (4WD position).


    C272067E01


    1. Disconnect the F47 four wheel drive control ECU connector.

    2. Disconnect the B53 transfer indicator switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-3 (4WD) - B53-2
      Always
      Below 1 Ω
      F47-3 (4WD) - Body ground
      Always
      100 kΩ or higher


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to Transfer Indicator Switch)
      If the result is not as specified, repair or replace the harness or connector.



  1. Check the transfer indicator switch (L4 position).


    C270605E01


    1. Disconnect the F47 four wheel drive control ECU connector.

    2. Disconnect the B54 transfer indicator switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-16 (4WDL) - B54-1
      Always
      Below 1 Ω
      F47-16 (4WDL) - Body ground
      Always
      100 kΩ or higher


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to Transfer Indicator Switch)
      If the result is not as specified, repair or replace the harness or connector.



6. INSPECT A.D.D. ACTUATOR


  1. Check the harness and connector (four wheel drive control ECU - A.D.D. actuator).

    1. Disconnect the F46 and F47 four wheel drive control ECU connectors.

    2. Disconnect the D1 A.D.D. actuator connector.



    3. Measure the resistance according to the value(s) in the table below.


      C217496E02

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-1 (DL1) - D1-6 (DL1)
      Always
      Below 1 Ω
      F47-1 (DL1) - Body ground
      Always
      100 kΩ or higher
      F47-2 (DL2) - D1-5 (DL2)
      Always
      Below 1 Ω
      F47-2 (DL2) - Body ground
      Always
      100 kΩ or higher
      F47-14 (ADD) - D1-3 (ADD)
      Always
      Below 1 Ω
      F47-14 (ADD) - Body ground
      Always
      100 kΩ or higher
      F46-2 (DM1) - D1-1 (DM1)
      Always
      Below 1 Ω
      F46-2 (DM1) - Body ground
      Always
      100 kΩ or higher
      F46-6 (DM2) - D1-2 (DM2)
      Always
      Below 1 Ω
      F46-6 (DM2) - Body ground
      Always
      100 kΩ or higher
      D1-4 (GND) - Body ground
      Always
      Below 1 Ω


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to A.D.D. Actuator)
      If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



  1. Check the four wheel drive control ECU (A.D.D. actuator).

    1. Connect the F46 and F47 four wheel drive control ECU connectors.

    2. Connect the D1 A.D.D. actuator connector.



    3. C217417E26
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-2 (DM1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H2 → H4, L4 (A.D.D. actuator motor stopped)
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H2 → H4, L4 (During operation of A.D.D. actuator motor from FREE to LOCK)
      10 to 14 V
      F46-6 (DM2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4, L4 → H2 (A.D.D. actuator motor stopped)
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4, L4 → H2 (During operation of A.D.D. actuator motor from LOCK to FREE)
      10 to 14 V
      F47-1 (DL1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H2
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4 or L4
      10 to 14 V
      F47-2 (DL2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4 or L4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H2
      10 to 14 V
      F47-14 (ADD) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4 or L4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H2
      10 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, determine if the malfunction is on the four wheel drive control ECU side or the actuator side by disconnecting the connector of the A.D.D. actuator, and then check the ECU output voltage.



  1. Check the four wheel drive control ECU.

    1. Connect the F46 and F47 four wheel drive control ECU connectors.

    2. Disconnect the D1 A.D.D. actuator connector.



    3. C217499E02
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      D1-3 (ADD) - D1-4 (GND)
      Ignition switch ON
      10 to 14 V
      D1-5 (DL2) - D1-4 (GND)
      Ignition switch ON
      10 to 14 V
      D1-6 (DL1) - D1-4 (GND)
      Ignition switch ON
      10 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to A.D.D. Actuator)
      If the result is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, inspect the A.D.D. actuator, because the voltage applied to the motor cannot be measured.



7. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


  1. Check the harness and connector between four wheel drive control ECU and transfer shift actuator assembly.

    1. Disconnect the B55 transfer shift actuator assembly connector.

    2. Disconnect the F47 and F46 four wheel drive control ECU connectors.



    3. Measure the resistance according to the value(s) in the table below.


      C270606E01

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F47-6 (TL1) - B55-5 (TL1)
      Always
      Below 1 Ω
      F47-6 (TL1) - Body ground
      Always
      100 kΩ or higher
      F47-7 (TL2) - B55-6 (TL2)
      Always
      Below 1 Ω
      F47-7 (TL2) - Body ground
      Always
      100 kΩ or higher
      F47-8 (TL3) - B55-3 (TL3)
      Always
      Below 1 Ω
      F47-8 (TL3) - Body ground
      Always
      100 kΩ or higher
      F46-8 (TM1) - B55-2 (TM1)
      Always
      Below 1 Ω
      F46-8 (TM1) - Body ground
      Always
      100 kΩ or higher
      F46-7 (TM2) - B55-1 (TM2)
      Always
      Below 1 Ω
      F46-7 (TM2) - Body ground
      Always
      100 kΩ or higher
      B55-4 (GND1) - Body ground
      Always
      Below 1 Ω


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Four Wheel Drive Control ECU)
      *b
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the four wheel drive control ECU output voltage.



  1. Check the four wheel drive control ECU.

    1. Connect the F47 and F46 four wheel drive control ECU connectors.

    2. Connect the B55 transfer shift actuator assembly connectors.



    3. C270936E01
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      F46-7 (TM2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch L4 → H4 (During operation of transfer shift actuator motor from LOW to HIGH)
      10 to 14 V
      Ignition switch ON
      Transfer position switch L4 → H4 (Transfer shift actuator motor stopped)
      Below 1.5 V
      F46-8 (TM1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4 → L4 (During operation of transfer shift actuator motor from HIGH to LOW)
      10 to 14 V
      Ignition switch ON
      Transfer position switch H4 → L4 (Transfer shift actuator motor stopped)
      Below 1.5 V
      F47-6 (TL1) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H2
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4 or L4
      10 to 14 V
      F47-7 (TL2) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch H4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H2 or L4
      10 to 14 V
      F47-8 (TL3) - F46-4 (GND)
      Ignition switch ON
      Transfer position switch L4
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H2 or H4
      10 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (Four Wheel Drive Control ECU)
      If the result is not as specified, determine if a malfunction is on the four wheel drive control ECU side or transfer shift actuator assembly side by disconnecting the connector of the transfer shift actuator assembly, and then check the four wheel drive control ECU output voltage.



  1. Check the four wheel drive control ECU output voltage.

    1. Disconnect the B55 transfer shift actuator assembly connector.

    2. Connect the F47 and F46 four wheel drive control ECU connector.



    3. C270607E01
    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      B55-3 (TL3) - B55-4 (GND1)
      Ignition switch ON
      10 to 14 V
      B55-5 (TL1) - B55-4 (GND1)
      Ignition switch ON
      10 to 14 V
      B55-6 (TL2) - B55-4 (GND1)
      Ignition switch ON
      10 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transfer Shift Actuator Assembly)
      If the result is not as specified, replace the four wheel drive control ECU (Click here). If the voltage is normal, inspect the transfer shift actuator assembly, because the voltage applied to the motor cannot be measured.



  1. Inspect the transfer shift actuator assembly.

    1. Remove the transfer shift actuator assembly (Click here).



    2. Check the H2 to H4 switch. Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the H2 to H4 position.

      NOTICE:
      1. Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.
      2. When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.

      HINT:
      When performing the operation described above, use the stop LP relay.



      C270608E01

      1. After the H2 to H4 switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        3 (TL3) - 4 (GND1)
        After H2 to H4 switch is complete
        100 kΩ or higher
        5 (TL1) - 4 (GND1)
        After H2 to H4 switch is complete
        Below 1 Ω
        6 (TL2) - 4 (GND1)
        After H2 to H4 switch is complete
        100 kΩ or higher


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        H2 to H4
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).



    3. Check the H4 to H2 switch. Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the H4 to H2 position.


      C270609E01

      1. After the H4 to H2 switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        3 (TL3) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher
        5 (TL1) - 4 (GND1)
        After H4 to H2 switch is complete
        Below 1 Ω
        6 (TL2) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        H4 to H2
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).



    4. Check the H4 to L4 switch. Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the H4 to L4 position.


      C270610E02

      1. After the H4 to L4 switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        3 (TL3) - 4 (GND1)
        After H4 to H2 switch is complete
        Below 1 Ω
        5 (TL1) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher
        6 (TL2) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        H4 to L4
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).



    5. Check the L4 to H4 switch. Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the H4 to L4 position.


      C270611E02

      1. After the L4 to H4 switch is complete, inspect the limit switch.

        Standard resistance:
        Tester Connection
        Condition
        Specified Condition
        3 (TL3) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher
        5 (TL1) - 4 (GND1)
        After H4 to H2 switch is complete
        100 kΩ or higher
        6 (TL2) - 4 (GND1)
        After H4 to H2 switch is complete
        Below 1 Ω


        Text in Illustration 
        *1
        Stop LP Relay
        -
        -
        *a
        Component without harness connected
        (Transfer Shift Actuator Assembly)
        *b
        L4 to H4
        If the result is not as specified, replace the transfer shift actuator assembly (Click here). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (Click here).