Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

  1. The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge.

NOTICE:
When the combination meter is removed or replaced, its connector is disconnected or fuel is added, the fuel receiver gauge display will return to normal within a maximum of 16 minutes after the ignition switch is turned to ON or when vehicle speed is input.


WIRING DIAGRAM


E200742E02


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

Result 
Result
Proceed to
CAN communication DTC is not output
A
CAN communication DTC is output
B


B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL METER OPERATION)
  1. Use the Active Test to check the operation of the fuel receiver gauge (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    Empty, 1/2, Full
    Confirm that the vehicle is stopped with the engine idling.

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING TECHSTREAM (FUEL INPUT)
  1. Use the Data List to check if the fuel receiver gauge is operating properly (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal/Min.: 0, Max.: 127.5
    Current fuel level displayed
    Unit: Liters

    OK:
    Fuel level signal displayed on the Techstream is almost the same as fuel receiver gauge indication.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)
  1. Disconnect the F14 meter connector.

  1. Disconnect the Q5 gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F14-40 (L) - Q5-2 (FS)
    Always
    Below 1 Ω
    F14-19 (E3) - Q5-3 (FE)
    Always
    Below 1 Ω
    F14-40 (L) - Body ground
    Always
    10 kΩ or higher
    F14-19 (E3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E180164E06
  1. Remove the fuel suction with pump and gauge tube assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 (FS) - B-2
    Always
    Below 1 Ω
    A-3 (FE) - B-3

Text in Illustration 
*a
Front view of wire harness connector
(to Fuel Sender Gauge Assembly)
*b
Lower Side (to Fuel Sender Gauge Assembly)
*c
Connector A
*d
Connector B


NG
REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (Click here)
OK


6.INSPECT FUEL SENDER GAUGE ASSEMBLY


    A223150E02
  1. Remove the fuel sender gauge assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 3
    Float level F (upper)
    12 to 18 Ω
    Float level E (lower)
    405 to 415 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Fuel Sender Gauge Assembly)
*b
Float level F (upper)
*c
Float level E (lower)


NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)