Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).



2. REMOVE REAR SEAT ASSEMBLY LH
  1. for 60/40 Split Double-folding Seat Type LH Side:
    Remove the rear seat assembly LH (Click here).

  1. for 60/40 Split Slide Walk-in Seat Type LH Side:
    Remove the rear seat assembly LH (Click here).



3. REMOVE REAR FLOOR SERVICE HOLE COVER


    A220797
  1. Remove the 3 screws and rear floor service hole cover.



4. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A220805
  1. for Standard Type:
    Remove the 6 bolts and No. 1 fuel tank protector.



    A224491
  1. for Half Cover Type:
    Remove the 4 bolts and No. 1 fuel tank protector.



5. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A220806
  1. Disconnect the fuel tank main tube (Click here).



6. DRAIN FUEL
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Operate the fuel pump and drain the fuel from the fuel tank main tube.

    CAUTION:
    1. Do not smoke or be near an open flame when working on the fuel system.
    2. Secure good ventilation.
    3. Keep gasoline away from rubber or leather parts.



    A225438
  1. Disconnect the fuel pump and sender gauge connector.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY


    A223269
  1. Disconnect the fuel return tube (Click here).



9. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    A225443
  1. Disconnect the fuel tank vent hose (Click here).



10. DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    A227934
  1. Disconnect the fuel tank breather tube (Click here).



11. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    A230980
  1. Disconnect the fuel tank to filler pipe hose from the filler pipe.



12. REMOVE FUEL TANK SUB-ASSEMBLY
  1. Place a transmission jack under the fuel tank.



    A220832
  1. Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.

  1. Slowly lower the transmission jack slightly.



13. REMOVE FUEL TANK CUSHION


    A220812E01
  1. Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion
    *2
    No. 2 Fuel Tank Cushion
    *3
    No. 3 Fuel Tank Cushion



14. REMOVE NO. 1 FUEL TANK PROTECTOR


    A232961
  1. Remove the No. 1 fuel tank protector from the fuel tank.



15. REMOVE FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    A227935
  1. Remove the fuel tank breather tube (Click here).



16. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY


    A220814E01
  1. Remove the 2 fuel tube joint clips and pull out the fuel tank main tube and fuel return tube.
    Text in Illustration 
    *1
    Fuel Tube
    *2
    Fuel Tube Joint
    *3
    Fuel Tube Joint Clip
    *4
    O-Ring

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



    A225442
  1. Remove the fuel tank main tube and fuel return tube from the fuel tank.



17. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    A220821E01
  1. Using SST, loosen the retainer.

    SST
    09808-14020  

    HINT:
    Fit the tips of SST onto the ribs of the retainer.

    NOTICE:
    1. When the retainer is loosened, be careful as the pump and gauge tube will spring upward from the force of the spring.
    2. Remove any foreign matter around the fuel suction with pump and gauge tube before this operation.

  1. Remove the retainer.

  1. Remove the fuel suction with pump and gauge tube assembly from the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.



18. REMOVE NO. 3 FUEL TANK PROTECTOR


    A220823
  1. Remove the 2 bolts.

  1. Detach the 4 clamps and remove the No. 3 fuel tank protector.



19. REMOVE FUEL TANK TO FILLER PIPE HOSE


    A230981
  1. Remove the fuel tank to filler pipe hose from the fuel tank.