Home › Engine / Hybrid System › 1GR-FE COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A223007E01
  1. Install a new gasket and the water pump assembly with the 17 bolts.

    Torque:
    for bolt A:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    for bolt C:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A226495E01
  1. Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

  1. Tighten bolts 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. INSTALL COOLER COMPRESSOR ASSEMBLY
(Click here)


4. INSTALL GENERATOR ASSEMBLY
(Click here)


5. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Attach the 2 wire harness clamps.

  1. Connect the 2 connectors.



6. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Separate Type:
    Install the 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies and 2 No. 2 idler pulley cover plates with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Integrated Type:
    Install the 2 No. 2 idler pulley sub-assemblies with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



7. INSTALL WATER INLET HOUSING


    A223008E01
  1. Install a new O-ring to the water outlet pipe.
    Text in Illustration 
    *1
    O-ring
    *2
    Gasket

  1. Install a new gasket to the water pump assembly.

  1. Apply soapy water to the gasket of the water outlet pipe.

  1. Install the water inlet housing with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 5 water by-pass hoses and slide the 5 hose clamps to secure them.

  1. Connect the No. 2 oil cooler hose and slide the hose clamp to secure the hose.

  1. Connect the oil cooler hose and slide the hose clamp to secure the hose.

  1. Connect the throttle body connector.



8. CONNECT AIR TUBE ASSEMBLY
  1. Connect the air tube assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the fan shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A229548E03
  1. Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.
    Text in Illustration 
    *a
    Paint Mark

  1. Temporarily install the fan with fluid coupling to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A223087
  1. Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the fan with fluid coupling and generator V-belt (Click here).

  1. Tighten the 4 nuts of the fan with fluid coupling.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. CONNECT OIL COOLER TUBE


    A226789
  1. Connect the oil cooler tube with the 2 bolts, and attach the claw to close the flexible hose clamp.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



11. INSTALL RADIATOR RESERVOIR TANK
  1. Install the radiator reservoir tank with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the reservoir hose to upper side of the radiator tank upper.



12. INSTALL NO. 2 RADIATOR HOSE


    A306026E03
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



    A227083E04
  1. Connect the No. 2 radiator hose with the clamp so that its paint mark aligns with the water inlet housing protrusion as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



13. INSTALL NO. 1 RADIATOR HOSE


    A227085E03
  1. Connect the No. 1 radiator hose to the water inlet housing with the clamp shown in the illustration labeled A.
    Text in Illustration 
    *a
    Paint Mark
    *b
    Protrusion
    *c
    Front
    *d
    Upper

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.

  1. Connect the No. 1 radiator hose with the clamp so that its paint mark aligns with the radiator protrusion as shown in the illustration labeled B.

    HINT:
    1. Make sure the paint mark of the No. 1 radiator hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.



14. INSTALL V-BANK COVER


    A229926E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



15. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    10.5 liters (11.1 US qts, 9.2 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the F line.
    If the coolant level is below the F line, repeat steps *4 through *8.
    If the coolant level is above the F line, drain coolant until the coolant level reaches the F line.



16. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.



17. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A224743
  1. Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



18. INSTALL FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 5 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



19. INSTALL AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)
  1. Install the air intake duct LH with the 2 screws.

  1. Install the clip and bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



20. INSTALL AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



21. INSTALL FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Install the front lower bumper cover with the 4 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



22. INSTALL COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)
  1. Install the cool air intake duct with the 4 clips.



23. INSTALL UPPER RADIATOR SUPPORT SEAL
  1. Install the upper radiator support seal with the 13 clips.