Home › Engine / Hybrid System › 1GR-FE COOLING › WATER PUMP

WATER PUMP > REMOVAL

for Preparation Click here



1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.



2. REMOVE COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)


    B353485
  1. Remove the 4 clips and cool air intake duct.



3. REMOVE FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Remove the clip, 5 bolts and front lower bumper cover.



4. REMOVE FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Remove the clip, 4 bolts and front lower bumper cover.



5. REMOVE AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)


    B353484
  1. Remove the clip and bolt.

  1. Remove the 2 screws and air intake duct LH.



6. REMOVE AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



7. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



8. DRAIN ENGINE COOLANT


CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



A273797E01


Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug (RH side)
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.



9. REMOVE V-BANK COVER


    A229925E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then detach the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



10. REMOVE NO. 1 RADIATOR HOSE


    A223076
  1. Loosen the 2 clamps and remove the No. 1 radiator hose.



11. REMOVE NO. 2 RADIATOR HOSE


    A223077
  1. Loosen the clamp and disconnect the No. 2 radiator hose from the water inlet.



    A306025
  1. Detach the clamp from the fan shroud.

  1. Loosen the clamp and remove the No. 2 radiator hose.



12. REMOVE RADIATOR RESERVOIR TANK


    A223079
  1. Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir tank.



13. DISCONNECT OIL COOLER TUBE


    A223080
  1. Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.



14. REMOVE FAN SHROUD


    A223082
  1. Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan with fluid coupling and generator V-belt (Click here).



    A223083
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



15. DISCONNECT AIR TUBE ASSEMBLY


    A223014
  1. Remove the 2 bolts and disconnect the air tube assembly.



16. REMOVE WATER INLET HOUSING
  1. Disconnect the throttle body connector.



    A306024E01
  1. Slide 5 hose clamps and disconnect the 5 water bypass hoses.
    Text in Illustration 
    *1
    No. 1 Water By-pass Hose
    *2
    No. 2 Water By-pass Hose
    *3
    No. 3 Water By-pass Hose
    *4
    No. 4 Water By-pass Hose
    *5
    No. 5 Water By-pass Hose
    *6
    Oil Cooler Hose
    *7
    No. 2 Oil Cooler Hose

  1. Slide the hose clamp and disconnect the oil cooler hose.

  1. Slide the hose clamp and disconnect the No. 2 oil cooler hose.



    A223012
  1. Remove the 5 bolts and water inlet housing.

  1. Remove the O-ring from the water outlet pipe.

  1. Remove the gasket from the water pump assembly.



17. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


A223006
  1. for Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies and 2 No. 2 idler pulley cover plates.

  1. for Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies.



18. DISCONNECT VANE PUMP ASSEMBLY


    A223016
  1. Disconnect the 2 connectors.

  1. Detach the 2 wire harness clamps.



    A223015
  1. Remove the 2 bolts and disconnect the vane pump assembly.



19. REMOVE GENERATOR ASSEMBLY
(Click here)


20. REMOVE COOLER COMPRESSOR ASSEMBLY
(Click here)


21. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



22. REMOVE WATER PUMP ASSEMBLY


    A223007
  1. Remove the 17 bolts, water pump assembly and gasket.