Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and occupant classification ECU.
If the center airbag sensor receives signals from the occupant classification ECU, it determines whether the instrument panel passenger airbag, lower No. 2 instrument panel airbag, front seat side airbag RH and front seat outer belt should be operated.
DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1650/32
One of the following conditions is met:
  1. An occupant classification system malfunction.
  2. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the occupant classification system circuit for 2 seconds.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Front seat wire RH
  3. Occupant classification system
  4. Center airbag sensor assembly

WIRING DIAGRAM


C213893E02


INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the ignition switch to ON, and wait for at least 10 seconds.

  1. Check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
OK


2.CHECK FOR DTC (CENTER AIRBAG SENSOR)
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650 is not output.

    HINT:
    Codes other than DTC B1650 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and occupant classification ECU.



    C215011E01
  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor



NG
REPLACE HARNESS AND CONNECTOR
OK


5.CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT


  1. Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.


    C213924E01


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor
    *3
    Connector E
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a9-8 (FSR+) - a9-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a9-8 (FSR+) - a9-4 (FSR-)
    Always
    1 MΩ or higher
    a9-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    a9-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a9-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    a9-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 6
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

6.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT WIRE RH)


  1. Turn the ignition switch off.


    C213925E01


    Text in Illustration 
    *1
    Occupant Classification ECU
    *2
    Center Airbag Sensor
    *3
    Front Seat Wire RH
    *4
    Floor Wire
    *5
    Connector C
    *6
    Connector B
    *7
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Na2-1 (FSR+) - Na2-4 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Na2-1 (FSR+) - Na2-4 (FSR-)
    Always
    1 MΩ or higher
    Na2-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Na2-4 (FSR-) - Body ground
    Always
    1 MΩ or higher

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Na2-1 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Na2-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH