Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight (HI-BEAM) Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives headlight dimmer switch information signals, and illuminates the high beam headlight.

WIRING DIAGRAM


E280744E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (DAYTIME RUNNING LIGHT)
  1. Using the Techstream, perform the Active Test (Click here).

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Running light relay
    ON/OFF
    -
    Head Light Hi
    Running light relay
    ON/OFF
    -

    OK:
    Running light relay operates (high beam headlights illuminate).



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (BATTERY - RUNNING LIGHT RELAY)
E205652E02
  1. Remove the running light relay from the engine room relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Running light relay terminal 6 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Running Light Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
  1. Remove the running light relay from the engine room relay block, junction block.

  1. Disconnect the 2C and 2D driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Running light relay terminal 4 (H) - 2D-24
    Always
    Below 1 Ω
    Running light relay terminal 2 (DRLS) - 2C-37
    Always
    Below 1 Ω
    Running light relay terminal 3 (E) - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Running light relay terminal 4 (H) or 2D-24 - Body ground
    Always
    10 kΩ or higher
    Running light relay terminal 2 (DRLS) or 2C-37 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY 

4.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
  1. Remove the driver side junction block assembly (Click here).


E280745E01

  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2D-24 - A-22 (DIM)
    Always
    Below 1 Ω
    2C-37 - A-25 (DRL)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Driver Side Junction Block Assembly)
    -
    -



NG
REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (Click here)
OK


5.REPLACE RUNNING LIGHT RELAY
  1. Replace the running light relay.

  1. Check that the daytime running lights operate normally (Click here).

OK:
The daytime running lights operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (RUNNING LIGHT RELAY WAS DEFECTIVE)