Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH closed
    11 to 14 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy light switch input
    Front door RH closed
    11 to 14 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    11 to 14 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    11 to 14 V
    F9-9 (L1) - Body ground
    B - Body ground
    Door control switch lock input
    Door control switch on
    Below 1 V
    F9-9 (L1) - Body ground
    B - Body ground
    Door control switch lock input
    Door control switch off
    Pulse generation (See waveform 1 or 2)
    F9-10 (UL1) - Body ground
    W - Body ground
    Door control switch unlock input
    Door control switch on
    Below 1 V
    F9-10 (UL1) - Body ground
    W - Body ground
    Door control switch unlock input
    Door control switch off
    Pulse generation (See waveform 3 or 4)
    F9-11 (L2) - Body ground
    LG - Body ground
    Driver side door key-linked lock input
    Driver side door key cylinder in lock position
    Below 1 V
    F9-11 (L2) - Body ground
    LG - Body ground
    Driver side door key-linked lock input
    Ignition switch off, all doors closed and driver side door key cylinder in neutral position
    Pulse generation (See waveform 5 or 6)
    F9-24 (UL3) - Body ground
    GR - Body ground
    Driver side door key-linked unlock input
    Driver side door key cylinder in unlock position
    Below 1 V
    F9-24 (UL3) - Body ground
    GR - Body ground
    Driver side door key-linked unlock input
    Ignition switch off, all doors closed and driver side door key cylinder in neutral position
    Pulse generation (See waveform 7 or 8)
    2B-3 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (except rear LH and back door)
    Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position
    Below 1 V
    2B-3 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (except rear LH and back door)
    Lock side of driver or passenger side door control switch pushed, or driver side door key cylinder in lock position
    11 to 14 V
    2F-8 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (for rear LH)
    Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position
    Below 1 V
    2F-8 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (for rear LH)
    Lock side of driver or passenger side door control switch pushed, or driver side door key cylinder in lock position
    11 to 14 V
    2B-1 (ACTD) - Body ground
    W - Body ground
    Driver side door lock motor unlock drive output
    Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position
    Below 1 V
    2B-1 (ACTD) - Body ground
    W - Body ground
    Driver side door lock motor unlock drive output
    Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    2B-2 (ACT-) - Body ground
    W - Body ground
    Door lock motor unlock drive output (for front RH and rear RH)
    Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position
    Below 1 V
    2B-2 (ACT-) - Body ground
    W - Body ground
    Door lock motor unlock drive output (for front RH and rear RH)
    Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    2F-10 (ACT-) - Body ground
    W - Body ground
    Door lock motor unlock drive output (for rear LH)
    Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position
    Below 1 V
    2F-10 (ACT-) - Body ground
    W - Body ground
    Door lock motor unlock drive output (for rear LH)
    Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position
    11 to 14 V
    2F-9 (TR+) - Body ground
    R - Body ground
    Back door unlock motor output
    Back door opener switch pushed
    Below 1 V
    2F-9 (TR+) - Body ground
    R - Body ground
    Back door unlock motor output
    Back door opener switch free
    11 to 14 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Front door LH unlocked
    Below 1 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Ignition switch off, all doors closed and front door LH locked
    Pulse generation (See waveform 9 or 10)
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Front door RH unlocked
    Below 1 V
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Ignition switch off, all doors closed and front door RH locked
    Pulse generation (See waveform 11 or 12)
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Ignition switch off, all doors closed and rear door LH locked
    Pulse generation (See waveform 13 or 14)
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Ignition switch off, all doors closed and rear door RH locked
    Pulse generation (See waveform 15 or 16)
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



  5. B201885E01
  6. Using an oscilloscope, check waveform 1
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-9 (L1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Door control switch off



  7. B201886E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-9 (L1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Door control switch off



  9. B199631E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-10 (UL1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Door control switch off



  11. B199632E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-10 (UL1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Door control switch off



  13. B201885E01
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door key cylinder in neutral position



  15. B201886E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door key cylinder in neutral position



  17. B199631E01
  18. Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-24 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder in neutral position



  19. B199632E01
  20. Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-24 (UL3) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and driver side door key cylinder in neutral position



  21. B199631E01
  22. Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  23. B199632E01
  24. Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  25. B199631E01
  26. Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  27. B199632E01
  28. Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  29. B199631E01
  30. Using an oscilloscope, check waveform 13.
    Waveform 13 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  31. B199632E01
  32. Using an oscilloscope, check waveform 14.
    Waveform 14 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  33. B201885E01
  34. Using an oscilloscope, check waveform 15.
    Waveform 15 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked



  35. B201886E01
  36. Using an oscilloscope, check waveform 16.
    Waveform 16 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked


CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B241165E01

  1. Disconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door closed
    Pulse generation (See waveform 1 or 2)
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door open
    Below 1 V
    W10-16 (BKL) - W10-8 (KEYE)*
    P - V
    Tail gate control switch lock input
    Back door lock key cylinder in neutral position
    Pulse generation (See waveform 3 or 4)
    W10-16 (BKL) - W10-8 (KEYE)*
    P - V
    Tail gate control switch lock input
    Back door lock key cylinder in lock position
    Below 1 V
    W10-15 (BKUL) - W10-8 (KEYE)*
    R - V
    Tail gate control switch unlock input
    Back door lock key cylinder in neutral position
    Pulse generation (See waveform 3 or 4)
    W10-15 (BKUL) - W10-8 (KEYE)*
    R - V
    Tail gate control switch unlock input
    Back door lock key cylinder in unlock position
    Below 1 V
    W10-24 (HSW+) - W10-7 (HSW-)
    GR - LG
    Back door opener switch input
    Back door opener switch off
    Pulse generation (See waveform 5 or 6)
    W10-24 (HSW+) - W10-7 (HSW-)
    GR - LG
    Back door opener switch input
    Back door opener switch on
    Below 1 V

    1. *: w/o Smart key System
    If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.



  5. B242623E02
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  7. B242624E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  9. B242623E02
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. W10-16 (BKL) - W10-8 (KEYE)
    2. W10-15 (BKUL) - W10-8 (KEYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door lock key cylinder in neutral position



  11. B242624E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. W10-16 (BKL) - W10-8 (KEYE)
    2. W10-15 (BKUL) - W10-8 (KEYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door lock key cylinder in neutral position



  13. B242623E02
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-24 (HSW+) - W10-7 (HSW-)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door opener switch off



  15. B242624E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-24 (HSW+) - W10-7 (HSW-)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door opener switch off


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)