Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Main Body ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Main Body ECU Communication Stop Mode
Either condition is met:
  1. "Main Body" is not displayed on the "CAN Bus Check" screen.
  2. "Main Body ECU Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside main body ECU (multiplex network body ECU)
  2. Main body ECU (multiplex network body ECU) branch wire or connector
  3. Main body ECU (multiplex network body ECU)

WIRING DIAGRAM


C217717E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU BRANCH WIRE)


    C212975E02
  1. Disconnect the F9 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F9-14 (CANH) - F9-13 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])



NG
REPAIR OR REPLACE MAIN BODY ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)


  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


    C215398E01


    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])
    *b
    Front view of wire harness connector
    (to Main Body ECU [Multiplex Network Body ECU])

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F10-3 (GND2) - Body ground
    Always
    Below 1 Ω
    A-11 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A-32 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    A-31 (ALTB) - Body ground
    Always
    11 to 14 V
    A-30 (BECU) - Body ground
    Always
    11 to 14 V
    A-29 (ACC) - Body ground
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)