Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Perform zero point calibration of the yaw rate and acceleration sensor and the test mode inspection.



1. INSPECT TIRES
  1. Inspect the tires (Click here).



2. MEASURE VEHICLE HEIGHT


D028453E03

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.

  1. Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    Measuring points:
    A:
    Ground clearance of the center of the front wheel
    B:
    Ground clearance of the center of the front adjusting cam bolt
    C:
    Ground clearance of the center of the rear wheel
    D:
    Ground clearance of the center of the rear lower control arm front side

    If the vehicle height is not as specified, adjust the height by pressing down on the vehicle several times to stabilize the suspension.

    Standard Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Grade
    Front (A - B)
    Rear (C - D)
    GRN280L-GKAGKA
    SR5
    115.9 mm (4.56 in.)
    79.9 mm (3.15 in.)
    S-Runner
    116.7 mm (4.59 in.)
    80.7 mm (3.18 in.)
    X-Runner
    117.2 mm (4.61 in.)
    85.4 mm (3.36 in.)
    GRN285L-GKAGKA
    SR5
    94.2 mm (3.71 in.)
    68.1 mm (2.68 in.)
    S-Runner
    94.9 mm (3.74 in.)
    68.8 mm (2.71 in.)
    Trail Edition
    95.6 mm (3.76 in.)
    69.8 mm (2.75 in.)
    Trail Edition
    (w/ KDSS)
    98.2 mm (3.87 in.)
    72.1 mm (2.84 in.)
    X-Runner
    97.6 mm (3.84 in.)
    72.5 mm (2.85 in.)

    NOTICE:
    The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


    C132440E16
  1. Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.
    Text in Illustration 
    *1
    Wheel Alignment Tester
    *2
    Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Standard Camber Inclination (Unloaded Vehicle):

    Vehicle Model
    Grade
    Camber Inclination
    Right-left Difference
    GRN280L-GKAGKA
    SR5
    -0°35' +/-45' (-0.58° +/-0.75°)
    45' (0.75°) or less
    S-Runner
    -0°37' +/-45' (-0.62° +/-0.75°)
    45' (0.75°) or less
    X-Runner
    -0°38' +/-45' (-0.63° +/-0.75°)
    45' (0.75°) or less
    GRN285L-GKAGKA
    SR5
    0°0' +/-45' (0.00°+/-0.75°)
    45' (0.75°) or less
    S-Runner
    -0°1' +/-45' (-0.02° +/-0.75°)
    45' (0.75°) or less
    Trail Edition
    -0°3' +/-45' (-0.05° +/-0.75°)
    45' (0.75°) or less
    Trail Edition
    (w/ KDSS)
    -0°7' +/-45' (-0.12° +/-0.75°)
    45' (0.75°) or less
    X-Runner
    -0°6' +/-45' (-0.10° +/-0.75°)
    45' (0.75°) or less


    Standard Caster Inclination (Unloaded Vehicle):

    Vehicle Model
    Grade
    Caster Inclination
    Right-left Difference
    GRN280L-GKAGKA
    SR5
    3°40' +/-45' (3.67° +/-0.75°)
    45' (0.75°) or less
    S-Runner
    3°40' +/-45' (3.67° +/-0.75°)
    45' (0.75°) or less
    X-Runner
    3°50' +/-45' (3.83° +/-0.75°)
    45' (0.75°) or less
    GRN285L-GKAGKA
    SR5
    3°13' +/-45' (3.22° +/-0.75°)
    45' (0.75°) or less
    S-Runner
    3°15' +/-45' (3.25° +/-0.75°)
    45' (0.75°) or less
    Trail Edition
    3°16' +/-45' (3.27° +/-0.75°)
    45' (0.75°) or less
    Trail Edition
    (w/ KDSS)
    3°21' +/-45' (3.35° +/-0.75°)
    45' (0.75°) or less
    X-Runner
    3°22' +/-45' (3.37° +/-0.75°)
    45' (0.75°) or less


    Standard Steering Axis Inclination (Unloaded Vehicle):

    Vehicle Model
    Grade
    Steering Axis Inclination
    GRN280L-GKAGKA
    SR5
    12°41' +/-45' (12.68° +/-0.75°)
    S-Runner
    12°42' +/-45' (12.70° +/-0.75°)
    X-Runner
    12°44' +/-45' (12.73° +/-0.75°)
    GRN285L-GKAGKA
    SR5
    12°10' +/-45' (12.17° +/-0.75°)
    S-Runner
    12°11' +/-45' (12.18° +/-0.75°)
    Trail Edition
    12°12' +/-45' (12.20° +/-0.75°)
    Trail Edition
    (w/ KDSS)
    12°16' +/-45' (12.27° +/-0.75°)
    X-Runner
    12°15' +/-45' (12.25° +/-0.75°)



4. ADJUST CAMBER AND CASTER

HINT:
After the camber has been adjusted, inspect the toe-in.

  1. Loosen the front adjusting cam bolt and rear adjusting cam nut.



  1. Turn the front adjusting cam and rear adjusting cam in both directions, and adjust the camber and caster to the center value.

    HINT:
    1. The camber and caster should be as close as possible to the center value.
    2. Adjust the camber and caster within +/-30'.



    G020169E04


    Text in Illustration 
    *1
    Front Adjusting Cam LH
    *2
    Front Adjusting Cam RH
    *3
    Rear Adjusting Cam LH
    *4
    Rear Adjusting Cam RH
    V100135
    Front
    -
    -



    G020414E04
  1. Read the adjustment chart (example).
    Text in Illustration 
    *1
    Caster
    *2
    Camber
    *3
    Front Adjusting Cam
    *4
    Rear Adjusting Cam
    *a
    Measured Value
    *b
    Standard Value

    1. Find the wheel alignment standard value applicable for the particular model.

    2. Mark the selected standard value on the adjustment chart.
      Standard Value (Reference) 
      Camber
      Caster
      0°00' (0.00°)
      3°30' (3.50°)

    3. Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.
      Measured Value (Reference) 
      Camber
      Caster
      -0°20' (-0.33°)
      3°20' (3.33°)



    4. As shown in the chart, read the distance from the marked point to 0, and adjust the front and/ or rear adjusting cams accordingly.
      Amount to Turn Adjusting Cams (by Gradation) 
      Front Adjusting Cam
      Rear Adjusting Cam
      +3
      +2


      C213231E04


      Text in Illustration 
      *a
      Camber
      *b
      Caster
      *c
      Front Cam Graduation
      *d
      Rear Cam Graduation



5. INSPECT TOE-IN


    SA03213E20
  1. Bounce the vehicle up and down at the corners to stabilize the suspension and inspect the toe-in.
    Text in Illustration 
    V100135
    Front

    Standard Toe-in (Unloaded Vehicle):

    Vehicle Model
    Grade
    Toe-in
    GRN280L-GKAGKA
    SR5
    A + B: 0°6' +/-0°10' (0.10° +/-0.16°)
    C - D: 2.52 +/-2 mm (0.10 +/-0.08 in.)
    S-Runner
    A + B: 0°5' +/-0°10' (0.08° +/-0.16°)
    C - D: 2.35 +/-2 mm (0.09 +/-0.08 in.)
    X-Runner
    A + B: 0°5' +/-0°10' (0.08° +/-0.16°)
    C - D: 2.16 +/-2 mm (0.09 +/-0.08 in.)
    GRN285L-GKAGKA
    SR5
    A + B: 0°6' +/-0°10' (0.10° +/-0.16°)
    C - D: 2.47 +/-2 mm (0.10 +/-0.08 in.)
    S-Runner
    A + B: 0°5' +/-0°10' (0.08° +/-0.16°)
    C - D: 2.29 +/-2 mm (0.09 +/-0.08 in.)
    Trail Edition
    A + B: 0°5' +/-0°10' (0.08° +/-0.16°)
    C - D: 2.11 +/-2 mm (0.08 +/-0.08 in.)
    Trail Edition
    (w/ KDSS)
    A + B: 0°3' +/-0°10' (0.05° +/-0.16°)
    C - D: 1.49 +/-2 mm (0.06 +/-0.08 in.)
    X-Runner
    A + B: 0°4' +/-0°10' (0.07° +/-0.16°)
    C - D: 1.60 +/-2 mm (0.06 +/-0.08 in.)

    If the toe-in is not within the specified range, adjust it at the rack ends.



6. ADJUST TOE-IN
  1. Detach the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.



    G020168E01
  1. Check that the lengths of the right and left rack ends are approximately the same.

    Standard difference:
    0 +/-1 mm (0 +/-0.0394 in.) or less

    Text in Illustration 
    *a
    Length
    V100135
    Lock Nut

  1. Tighten the tie rod end lock nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.



7. INSPECT WHEEL ANGLE


    F046953E12
  1. Turn the steering wheel to the left and right full lock positions, and measure the turning angle.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front

    Standard Wheel Turning Angle (Unloaded Vehicle):

    Vehicle Model
    Grade
    Inside Wheel Angle
    Outside Wheel Angle: Reference
    GRN280L-GKAGKA
    SR5
    29°49' to 32°49'
    (29.82° to 32.82°)
    29°34'
    (29.57°)
    S-Runner
    29°48' to 32°48'
    (29.80° to 32.80°)
    29°33'
    (29.55°)
    X-Runner
    29°47' to 32°47'
    (29.78° to 32.78°)
    29°31'
    (29.52°)
    GRN285L-GKAGKA
    SR5
    30°21' to 33°21'
    (30.35° to 33.35°)
    29°29'
    (29.48°)
    S-Runner
    30°20' to 33°20'
    (30.33° to 33.33°)
    29°28'
    (29.47°)
    Trail Edition
    30°20' to 33°20'
    (30.33° to 33.33°)
    29°27'
    (29.45°)
    Trail Edition
    (w/ KDSS)
    30°17' to 33°17'
    (30.28° to 33.28°)
    29°23'
    (29.38°)
    X-Runner
    30°18' to 33°18'
    (30.30° to 33.30°)
    29°24'
    (29.40°)

    If the right and left inside wheel angles differ from the specified range, check the right and left rack end lengths.



8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

HINT:
Perform the yaw rate sensor zero point calibration (Click here).



10. PERFORM INITIALIZATION

HINT:
Some systems need to be initialized after the wheel alignment is adjusted (Click here).