Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU) (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH open
    Below 1 V
    2F-27 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy switch input
    Front door LH closed
    11 to 14 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH open
    Below 1 V
    2B-15 (FRCY) - Body ground
    B - Body ground
    Front door RH courtesy switch input
    Front door RH closed
    11 to 14 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    F8-3 (LCTY) - Body ground
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    11 to 14 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    F10-27 (RCTY) - Body ground
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    11 to 14 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Front door LH unlocked
    Below 1 V
    F9-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Ignition switch off, all doors closed and front door LH locked
    Pulse generation (see waveform 1 or 2)
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Front door RH unlocked
    Below 1 V
    F9-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Ignition switch off, all doors closed and front door RH locked
    Pulse generation (see waveform 3 or 4)
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2F-25 (LSWL) - Body ground
    V - Body ground
    Rear door LH lock position switch input
    Ignition switch off, all doors closed and rear door LH locked
    Pulse generation (see waveform 5 or 6)
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    F10-2 (LSWR) - Body ground
    V - Body ground
    Rear door RH lock position switch input
    Ignition switch off, all doors closed and rear door RH locked
    Pulse generation (see waveform 7 or 8)
    F9-25 (PRG) - Body ground
    LG - Body ground
    Door control receiver output
    Key in ignition key cylinder → No key in ignition key cylinder
    Pulse generation
    F9-26 (RDA) - Body ground
    P - Body ground
    Door control receiver input
    No key in ignition key cylinder, all doors closed and transmitter switch off → on
    Pulse generation
    2D-13 (BZR) - Body ground
    GR - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    2D-13 (BZR) - Body ground
    GR - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer on
    11 to 14 V
    F9-3 (HAZ) - Body ground
    W - Body ground
    Hazard warning signal light signal output
    Hazard warning signal switch off
    Below 1 V
    F9-3 (HAZ) - Body ground
    W - Body ground
    Hazard warning signal light signal output
    Hazard warning signal switch on
    11 to 14 V
    F9-17 (KSW) - Body ground
    B - Body ground
    Unlock warning switch input
    No key in ignition key cylinder
    10 kΩ or higher
    F9-17 (KSW) - Body ground
    B - Body ground
    Unlock warning switch input
    Key in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



  5. B199631E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  7. B199632E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door LH locked



  9. B201885E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  11. B201886E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F9-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and front door RH locked



  13. B201885E01
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  15. B201886E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2F-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door LH locked



  17. B201885E01
  18. Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked



  19. B201886E01
  20. Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    F10-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and rear door RH locked


CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B241165E01

  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the V2 multiplex network door ECU (back door P/W) connector.

  4. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door closed
    Pulse generation (see waveform 1 or 2)
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy switch input
    Back door open
    Below 1 V
    If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.



  5. B245381E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed



  7. B245382E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    W10-10 (BDCY) - W10-18 (CTYE)
    Tool Setting
    5 V/DIV., 10 ms/DIV.
    Condition
    Back door closed