Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Install the main body ECU (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F8-3 (LCTY) - 2B-4 (GND1)
    V - W-B
    Rear door courtesy light switch LH signal
    Rear door LH open
    Below 1 V
    Rear door LH closed
    11 to 14 V
    F9-2 (DOMR) - 2B-4 (GND1)
    V - W-B
    DOME relay drive output
    Battery saving control not operating
    11 to 14 V
    Battery saving control operating
    Below 1 V
    F10-27 (RCTY) - 2B-4 (GND1)
    R - W-B
    Rear door courtesy light switch RH signal
    Rear door RH open
    Below 1 V
    Rear door RH closed
    11 to 14 V
    F10-4 (MILE) - 2B-4 (GND1)*1
    W - W-B
    Door mirror foot light signal output
    Door mirror foot light on
    11 to 14 V
    Door mirror foot light off
    Below 1 V
    2B-18 (ILE) - 2B-4 (GND1)
    G - W-B
    Interior light signal
    Interior light on
    Below 1 V
    Interior light off
    11 to 14 V
    2B-15 (FRCY) - 2B-4 (GND1)
    B - W-B
    Front door courtesy light switch RH signal
    Front door RH open
    Below 1 V
    Front door RH closed
    11 to 14 V
    2B-36 (FSPT) - 2B-4 (GND1)*2, *3
    SB - W-B
    Front door inside handle illumination, rear door inside handle illumination RH and interior foot light signal
    Front door inside handle illumination and interior foot light on
    Below 1 V
    Front door inside handle illumination and interior foot light off
    11 to 14 V
    2F-27 (FLCY) - 2B-4 (GND1)
    R - W-B
    Front door courtesy light switch LH signal
    Front door LH open
    Below 1 V
    Front door LH closed
    11 to 14 V
    2F-36 (FSPT) - 2B-4 (GND1)*2
    SB - W-B
    Rear door inside handle illumination LH signal
    Rear door inside handle illumination on
    Below 1 V
    Rear door inside handle illumination off
    11 to 14 V

    1. *1: w/ Door Mirror Foot Light
    2. *2: w/ Inside Handle Illumination
    3. *3: w/ Interior Foot Light
    If the result is not as specified, the main body ECU may have a malfunction.


CHECK MULTIPLEX NETWORK DOOR ECU

E199768E01

  1. Disconnect the V2 and W10 multiplex network door ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-17 (B1) - Body ground
    R - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the V2 and W10 multiplex network door ECU connectors.



  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W10-10 (BDCY) - W10-18 (CTYE)
    P - G
    Back door courtesy light switch signal
    Back door open
    Below 1 V
    Back door closed
    Pulse generation
    (See waveform 1 or 2)
    W10-22 (LGLP) - V2-6 (GND)
    L - W-B
    Spot light LH signal
    Spot light LH on
    Pulse generation
    (See waveform 3)
    Spot light LH off
    Pulse generation
    (See waveform 4)
    W10-23 (LGP2) - V2-6 (GND)
    L - W-B
    Spot light RH signal
    Spot light RH on
    Pulse generation
    (See waveform 3)
    Spot light RH off
    Pulse generation
    (See waveform 4)
    W10-25 (B2) - V2-6 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V
    W10-26 (B3) - V2-6 (GND)
    R - W-B
    Battery power supply
    Always
    11 to 14 V



      B242623E04
    1. Waveform 1
      Item
      Content
      Terminal No. (Symbol)
      W10-10 (BDCY) - W10-18 (CTYE)
      Tool setting
      5 V/DIV., 10 ms/DIV.
      Condition
      Back door closed



    2. B242624E01
    3. Waveform 2
      Item
      Content
      Terminal No. (Symbol)
      W10-10 (BDCY) - W10-18 (CTYE)
      Tool setting
      5 V/DIV., 10 ms/DIV.
      Condition
      Back door closed



    4. B242650E01
    5. Waveform 3
      Item
      Content
      Terminal No. (Symbol)
      W10-22 (LGLP) - V2-6 (GND)
      W10-23 (LGP2) - V2-6 (GND)
      Tool setting
      5 V/DIV., 200 ms/DIV.
      Condition
      1. Spot light LH on
      2. Spot light RH on



    6. B242652E01
    7. Waveform 4
      Item
      Content
      Terminal No. (Symbol)
      W10-22 (LGLP) - V2-6 (GND)
      W10-23 (LGP2) - V2-6 (GND)
      Tool setting
      5 V/DIV., 200 ms/DIV.
      Condition
      1. Spot light LH off
      2. Spot light RH off