Home › Drivetrain ยท VF2BM TRANSFER / 4WD / AWD › TRANSFER CASE FRONT OIL SEAL

TRANSFER CASE FRONT OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL


C216677
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



2. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


3. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    F043429E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    C216517E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



4. REMOVE FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL
  1. Using a screwdriver and hammer, tap out the oil seal from the companion flange.

    NOTICE:
    Be careful not to damage the oil seal and companion flange contact surfaces.



5. REMOVE TRANSFER CASE FRONT OIL SEAL


C205243E01
  1. Using SST, tap out the transfer case front oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the transfer case front oil seal and front case contact surface.



6. INSTALL TRANSFER CASE FRONT OIL SEAL


C205242E01
  1. Coat the lip of a new transfer case front oil seal with MP grease.

  1. Using SST and a hammer, tap in the transfer case front oil seal until its metal ring contacts the front case.

    SST
    09649-17010  
    09950-70010   (09951-07100)



7. INSTALL FRONT TRANSFER OUTPUT SHAFT COMPANION FLANGE OIL SEAL


    F043517E02
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

  1. Coat the lip of the oil seal with MP grease.



8. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


C217366E01
  1. Apply gear oil to the connecting areas of the companion flange and driven sprocket.

  1. Install the companion flange to the driven sprocket.
    Text in Illustration 
    V100135
    Front

  1. Using SST to hold the companion flange, install a new lock nut.

    SST
    09330-00021  

    Torque:
    118 N*m{ 1203 kgf*cm , 87 ft.*lbf }



    F050151E02
  1. Using a chisel and hammer, stake the lock nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Securely stake the shaft to the lock nut groove.
    2. Be careful not to damage the parts around the lock nut.
    3. Do not apply excessive force to the shaft.



9. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


10. ADD TRANSFER OIL
  1. Remove the filler plug and gasket.

  1. Add oil so that the oil level is between 0 to 5.0 mm (0 to 0.196 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Add oil slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

    HINT:
    1. Viscosity:
      SAE 75W

      Capacity:
      1.4 liters (1.5 US qts, 1.2 lmp.qts)

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket to the filler plug and then tighten the plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. CHECK FOR TRANSFER OIL LEAK