Home › Drivetrain ยท AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER OIL SEAL (for 4WD)

FRONT DIFFERENTIAL CARRIER OIL SEAL (for 4WD) > REPLACEMENT

for Preparation Click here



1. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY
  1. Remove the front differential carrier assembly (Click here).



2. REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT


C089309E05
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  



    B087842E06
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)
    Text in Illustration 
    *a
    Turn
    *b
    Hold



3. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F040720E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



4. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL


F040717E07
  1. Using SST, remove the oil seal.

    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger



5. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


6. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


F044343E03
  1. Using SST, remove the roller bearing (inner).

    SST
    09556-22010  



    W001770E06
  1. Using SST, tap out the roller bearing (outer).

    SST
    09308-00010  



7. REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a screwdriver and hammer, tap out the oil storage ring.



8. REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER


    C093595E01
  1. Remove the bearing spacer.



9. INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new bearing spacer.

    HINT:
    Install the spacer so that it is facing in the correct direction.



10. INSTALL FRONT DIFFERENTIAL OIL STORAGE RING
  1. Using a brass bar and hammer, tap in a new oil storage ring.

    NOTICE:
    Be careful not to damage the oil storage ring.



11. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


G021735E01
  1. Using SST and a hammer, install the roller bearing (outer).

    SST
    09316-60011   (09316-00011, 09316-00021)

  1. Install the roller bearing (inner).



12. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


13. INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL


F040719E09
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09554-22010  

    Oil seal depth:
    3.9 to 4.8 mm (0.154 to 0.188 in.)

    Text in Illustration 
    *a
    Oil Seal Depth



14. INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F040716E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.

  1. Using SST to hold the companion flange, install the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    370 N*m{ 3770 kgf*cm , 273 ft.*lbf } or less



15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
  1. Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    0.98 to 1.57 N*m (10 to 16 kgf*cm, 8.7 to 13.9 in.*lbf)
    Used bearing
    0.49 to 0.78 N*m (5 to 8 kgf*cm, 4.3 to 6.9 in.*lbf)

    If the result is not as specified, adjust the preload.

    Standard Total Preload (at Starting):
    Item
    Specified Condition
    New bearing
    1.2 to 2.45 N*m (12 to 25 kgf*cm, 10.6 to 21.7 in.*lbf)
    Used bearing
    0.71 to 1.66 N*m (7.2 to 17 kgf*cm, 6.3 to 14.7 in.*lbf)



16. STAKE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT


C089310E01
  1. Using a chisel and hammer, stake the nut.



17. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
  1. Install the front differential carrier assembly (Click here).