Home › Engine / Hybrid System › 1GR-FE COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.



2. REMOVE COOL AIR INTAKE DUCT (for 4WD with Intuitive Parking Assist System)


    B353485
  1. Remove the 4 clips and cool air intake duct.



3. REMOVE FRONT LOWER BUMPER COVER (w/o Intuitive Parking Assist System)
  1. Remove the clip, 5 bolts and front lower bumper cover.



4. REMOVE FRONT LOWER BUMPER COVER (w/ Intuitive Parking Assist System)
  1. Remove the clip, 4 bolts and front lower bumper cover.



5. REMOVE AIR INTAKE DUCT LH (w/ Intuitive Parking Assist System)


    B353484
  1. Remove the clip and bolt.

  1. Remove the 2 screws and air intake duct LH.



6. REMOVE AIR INTAKE DUCT RH (w/ Intuitive Parking Assist System)

HINT:
Use the same procedure as for the LH side.



7. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.



    A224743
  1. Unhook the No. 1 engine under cover sub-assembly from the vehicle body as shown in the illustration.



8. DRAIN ENGINE COOLANT


CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



A273797E01


Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug (RH side)
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.



9. REMOVE V-BANK COVER


    A229925E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then detach the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    V-bank Cover Hook



10. REMOVE FRONT BUMPER COVER
w/o Intuitive Parking Assist System: (Click here)
w/ Intuitive Parking Assist System: (Click here)


11. REMOVE UPPER FRONT BUMPER RETAINER


    A311025
  1. Remove the 3 bolts, 2 screws and upper front bumper retainer.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Screw



12. REMOVE RADIATOR SIDE DEFLECTOR RH


    A311026
  1. Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector RH so that the radiator can be removed in the step below.



13. REMOVE RADIATOR SIDE DEFLECTOR LH


    A311027
  1. Using a clip remover, detach the 3 claws and remove the clip. Then move the radiator side deflector LH so that the radiator can be removed in the step below.



14. REMOVE NO. 1 RADIATOR HOSE


    A223076
  1. Loosen the 2 clamps and remove the No. 1 radiator hose.



15. REMOVE NO. 2 RADIATOR HOSE


    A223077
  1. Loosen the clamp and disconnect the No. 2 radiator hose from the water inlet.



    A306025
  1. Detach the clamp from the fan shroud.

  1. Loosen the clamp and remove the No. 2 radiator hose.



16. REMOVE RADIATOR RESERVOIR TANK


    A223079
  1. Disconnect the reservoir hose from the upper side of the radiator tank.

  1. Remove the 3 bolts and radiator reservoir tank.



17. DISCONNECT OIL COOLER TUBE


    A223080
  1. Detach the claw to open the flexible hose clamp, and then remove the 2 bolts to disconnect the oil cooler tube from the fan shroud.



18. REMOVE FAN SHROUD


    A223082
  1. Loosen the 4 nuts holding the fan with fluid coupling.

  1. Remove the fan with fluid coupling and generator V-belt (Click here).



    A223083
  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fan with fluid coupling, and then remove the shroud together with the fan with fluid coupling.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



19. REMOVE RADIATOR ASSEMBLY


    A224905
  1. Slide the 2 clamps and disconnect the 2 oil cooler hoses.



    A224957
  1. Remove the 4 bolts and radiator.



20. REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
  1. Remove the No. 1 radiator to support seal from the radiator assembly.



21. REMOVE NO. 2 RADIATOR TO SUPPORT SEAL
  1. Remove the No. 2 radiator to support seal from the radiator assembly.