Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0657    Actuator Supply Voltage Circuit / Open

for Preparation Click here


DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the ignition switch is turned off. If the output voltage is 7 V or higher when the ignition switch is turned off, the ECM will illuminate the MIL and store this DTC when the ignition switch is turned to ON.

DTC No.
DTC Detection Condition
Trouble Area
P0657
There is a throttle actuator power supply error.
ECM

MONITOR STRATEGY


Related DTC
P0657: ETCS power supply
Required sensors/Components (Main)
ECM
Required sensors/Components (Related)
Throttle actuator
Frequency of Operation
Once per driving cycle
Duration
Within 1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor will run whenever this DTC is not present
None
Throttle actuator power supply voltage
7 V or higher

TYPICAL MALFUNCTION THRESHOLDS


Ignition switch
From ON to off (Temporary Fail ON)
Throttle actuator power supply
ON

CONFIRMATION DRIVING PATTERN


A199238E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the Techstream off.
  5. Turn the ignition switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) battery terminal.
  9. Turn the ignition switch to ON.
  10. Wait 10 seconds or more.
  11. Turn the ignition switch off.
  12. Wait 15 seconds or more.
  13. Connect the Techstream to the DLC3.
  14. Turn the ignition switch to ON and turn the Techstream on [A].
  15. Wait 5 seconds or more.
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  17. Read the DTCs.

    HINT:
    1. If a DTC is output, the system is malfunctioning.
    2. If a DTC is not output, perform the following procedure.

  18. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  19. Input the DTC: P0657.
  20. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  21. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (P0657)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON for 10 seconds.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.
    Result 
    Display (DTC Output)
    Proceed to
    P0657
    A
    No DTC output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)