Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM

DTC    C1812/12    Pressure Sensor Malfunction / Upside

for Preparation Click here


DESCRIPTION

In the KDSS hydraulic circuit, the fluid is contained under pressure. If the fluid temperature is 20°C (68°F), the pressure is approximately 3.0 MPa (30.6 kgf/cm2, 435 psi).

DTC Code
DTC Detection Condition
Trouble Area
C1812/12
One of the following conditions is met:
  1. The sensor power source voltage (SBP1 terminal) is 4.3 V or less for 0.5 seconds with the ignition switch ON.
  2. The sensor power source voltage (SBP1 terminal) is 5.5 V or higher for 0.5 seconds with the ignition switch ON.
  3. The sensor output (SOP1 terminal) is 0.3 V or less for 1 second with the ignition switch ON.
  4. The sensor output (SOP1 terminal) is 4.7 V or higher for a second with the ignition switch ON.
  1. Harness or connector
  2. Accumulator pressure sensor (Stabilizer control with accumulator housing assembly)
  3. Stabilizer control ECU

WIRING DIAGRAM


C215167E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (OIL PRESSURE SENSOR)

NOTICE:
  1. Perform the inspection on a level surface.
  2. Perform the inspection with the vehicle empty.
  3. Make sure that the wheels are on the ground and facing straight ahead.
  4. Perform the inspection with the vehicle load completely on the suspension.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / KDSS / Data List.

  1. Select the item below in the Data List, and read the value displayed on the Techstream.

    KDSS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure Sensor
    Oil pressure sensor/
    Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
    Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
    2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)
    -

  1. Check the fluid pressure.

    OK:
    2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi)



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE STABILIZER CONTROL ECU (Click here)  

3.INSPECT STABILIZER CONTROL ECU (SBP1 VOLTAGE)
  1. Connect the stabilizer control ECU connector.

  1. Disconnect the stabilizer control with accumulator housing connector.



    C215182E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O23-3 (SBP1) - Body ground
    Ignition switch ON
    4.75 to 5.25 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stabilizer Control with Accumulator Housing Assembly)



NG
Go to step 7
OK


4.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)
  1. Disconnect the stabilizer control ECU connector.

  1. Disconnect the stabilizer control with accumulator housing connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F70-17 (SOP1) - O23-2 (SOP1)
    Always
    Below 1 Ω
    F70-17 (SOP1) - Body ground
    Always
    10 kΩ or higher
    F70-6 (SGP1) - O23-1 (SGP1)
    Always
    Below 1 Ω
    F70-6 (SGP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT ACCUMULATOR PRESSURE SENSOR (OUTPUT VOLTAGE)
  1. Connect the stabilizer control ECU connector.

  1. Connect the stabilizer control with accumulator housing connector.



    C215883E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F70-17 (SOP1) - Body ground
    Ignition switch ON
    0.4 to 4.6 V

    Text in Illustration 
    *a
    Component with harness connected
    (Stabilizer Control ECU)



NG
Go to step 6
OK

REPLACE STABILIZER CONTROL ECU (Click here)  

6.READ VALUE USING TECHSTREAM (OIL PRESSURE SENSOR)
  1. Disconnect the stabilizer control with accumulator housing connector.

  1. Connect the stabilizer control ECU connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / KDSS / Data List.

  1. Select the item below in the Data List, and read the value displayed on the Techstream.

    KDSS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure Sensor
    Oil pressure sensor/
    Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
    Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)
    2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)
    -



    C215166E01
  1. Using a 1.5 V dry cell battery, connect the positive (+) lead to terminal 2 (SOP1) of the stabilizer control with accumulator housing connector and the negative (-) lead to terminal 1 (SGP1), and check that the Data List display changes.

    OK:
    Data List display changes.

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stabilizer Control with Accumulator Housing Assembly)



NG
REPLACE STABILIZER CONTROL ECU (Click here)
OK

REPLACE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - ACCUMULATOR PRESSURE SENSOR)
  1. Disconnect the stabilizer control ECU connector.

  1. Disconnect the stabilizer control with accumulator housing connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F70-15 (SBP1) - O23-3 (SBP1)
    Always
    Below 1 Ω
    F70-15 (SBP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STABILIZER CONTROL ECU (Click here)