Home › Suspension › SUSPENSION CONTROL › KINETIC DYNAMIC SUSPENSION SYSTEM

DTC    C1831/31    Accumulator Solenoid Malfunction / Upside

DTC    C1832/32    Accumulator Solenoid Malfunction / Downside

for Preparation Click here


DESCRIPTION

The stabilizer control ECU receives information from the steering angle sensor, skid control ECU (speed signal) and yaw rate and acceleration sensor via CAN communication. Based on this information, the stabilizer control ECU turns the stabilizer control solenoid valve (built into the stabilizer control with accumulator housing assembly) on or off.

DTC Code
DTC Detection Condition
Trouble Area
C1831/31
C1832/32
Either condition is met:
  1. An open circuit signal is detected for 1 second continuously when current is not applied to the solenoid valve.
  2. A short circuit signal is detected 8 times continuously when current is applied to the solenoid valve.
  1. Harness or connector
  2. Stabilizer control solenoid valve (Stabilizer control with accumulator housing assembly)
  3. Stabilizer control ECU

WIRING DIAGRAM


C215168E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (ACCUMULATOR VALVE)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / KDSS / Data List.

  1. Select the item below in the Data List, and read the value displayed on the Techstream.

    KDSS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Valve (Downside)
    Stabilizer control solenoid valve (for Lower Chamber)/
    ON or OFF
    ON: Stabilizer control solenoid valve closed
    OFF: Stabilizer control solenoid valve open
    -
    Accumulator Valve (Upside)
    Stabilizer control solenoid valve (for Upper Chamber)/
    ON or OFF
    ON: Stabilizer control solenoid valve open
    OFF: Stabilizer control solenoid valve closed
    -

  1. Perform the Active Test of the stabilizer control ECU using the Techstream.

    KDSS 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Accumulator Valve (Upside)
    Stabilizer control solenoid valve (for Upper Chamber)
    Valve ON / OFF
    The operating sound of the solenoid (clicking sound) can be heard.
    ON: Data List ON
    OFF: Data List OFF
    When the Active Test is performed, the solenoid turns on for 3 seconds.
    Accumulator Valve (Downside)
    Stabilizer control solenoid valve (for Lower Chamber)
    Valve ON / OFF
    The operating sound of the solenoid (clicking sound) can be heard.
    ON: Data List ON
    OFF: Data List OFF
    When the Active Test is performed, the solenoid turns on for 3 seconds.

  1. Check that the solenoid operating sound can be heard, and that the Data List display changes between ON and OFF in response to the Active Test.

OK:
Solenoid operating sound can be heard and display changes between ON and OFF in response to Active Test.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE STABILIZER CONTROL ECU (Click here)  

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - STABILIZER CONTROL SOLENOID VALVE)
  1. Disconnect the stabilizer control ECU connector.

  1. Disconnect the stabilizer control with accumulator housing assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F70-3 (SLAU) - O23-6 (SLAU)
    Always
    Below 1 Ω
    F70-3 (SLAU) - Body ground
    Always
    10 kΩ or higher
    F70-1 (SLAL) - O23-5 (SLAL)
    Always
    Below 1 Ω
    F70-1 (SLAL) - Body ground
    Always
    10 kΩ or higher
    O23-4 (AUG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT STABILIZER CONTROL SOLENOID VALVE
  1. Disconnect the stabilizer control with accumulator housing assembly connector.



    C215163E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for DTC C1831/31 (for Upper Chamber) 
    Tester Connection
    Condition
    Specified Condition
    5 (SLAL) - 4 (AUG)
    25°C (77°F)
    24.3 to 25.7 Ω
    for DTC C1832/32 (for Lower Chamber) 
    Tester Connection
    Condition
    Specified Condition
    6 (SLAU) - 4 (AUG)
    25°C (77°F)
    24.3 to 25.7 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Stabilizer Control with Accumulator Housing Assembly)



  1. Check for an operating sound of the stabilizer control solenoid valve.



      C215165E01
    1. for DTC C1831/31 (for Upper Chamber):
      Connect terminal 5 (SLAL) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

      OK:
      An operating sound (click sound) can be heard.

      Text in Illustration 
      *a
      Component without harness connected
      (Stabilizer Control with Accumulator Housing Assembly)



    2. C215164E01
    3. for DTC C1832/32 (for Lower Chamber):
      Connect terminal 6 (SLAU) to the positive (+) battery terminal, and terminal 4 (AUG) to the negative (-) battery terminal.

      OK:
      An operating sound (click sound) can be heard.

      Text in Illustration 
      *a
      Component without harness connected
      (Stabilizer Control with Accumulator Housing Assembly)



NG
REPLACE STABILIZER CONTROL WITH ACCUMULATOR HOUSING ASSEMBLY (Click here)
OK

REPLACE STABILIZER CONTROL ECU (Click here)